Products

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Cantrail Seal fits along the cantrail at the top of the rear cab, sealing the upper joint where the cab meets the roof. It runs the length of the ...

Door Seal for the rear end door, fitting along the lower floor edge of the side-hinged tailboard. It forms the sealing interface between the foot o...

Bolt

Inner Sill is a structural body panel forming the inner section of the sill assembly beneath the door aperture, running along the lower edge of the...

Sill Protector in aluminium, forming part of the external body protection for the sill panel below the door aperture. The panel covers the outer f...

Sill Protector in aluminium, fitted over the outer sill panel below the door apertures to shield the original sill from stone chips, mud abrasion a...

Sill Protector in aluminium, fitted over the outer sill panel below the door apertures to shield the original sill from stone chips, mud abrasion a...

Differential Cover is the pressed plate that closes the differential aperture in the axle casing, retaining the axle oil and giving access to the c...

Rear Door Protection Plate mounts on the exterior of the rear door to shield the panel from stone chips, scuffs and impact damage during loading an...

Rear Sill Panel - Right-Hand is a lower-body repair panel for the rear sill section on the offside (right-hand) of the body. It forms the outer clo...

Quarterback chassis for Serie 2/3 88" military, including Lightweight. The rear spring leaf supports are included, as well as the support of the fi...

Battery Carrier is the mounting tray that holds and locates the battery, supporting it and retaining it against movement and vibration. It forms t...

Trailer Plug - a 7-pin towing connector that links the towing vehicle's electrical circuit to a trailer or caravan. It carries the supply for the t...

Fuel Tank Outrigger is a lateral chassis support bracket within the main frame structure. Welded to the chassis side rail, it carries the front mo...

Front door pillar repair section for the left-hand side — the A-post that forms the rear edge of the bulkhead and carries the front door hinges. T...

Door Pillar Bracket for the right-hand (offside) bulkhead door pillar, supplied as the bottom bracket only (less the pillar). The bracket forms th...

Chassis front crossmember Series LHD & RHD (WITHOUT the front chassis legs)

Lamp Boot - Military is a rubber protective boot for military-specification lamp assemblies. The boot fits over the lamp body to provide a weather...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Washer is a nylon door hinge washer used on the hinge fixing bolts. It fits over the hinge bolt as a low-friction spacer between the moving hinge ...

Captive Nut with a UNF thread, providing a fixed threaded anchor point for a bolted fixing. The nut is retained in its bracket or panel so it cann...

Door Hinge Bolt - countersunk UNF type - within the door assembly. This countersunk fixing bolt secures the door hinge plate to the door face, com...

Wing Fixing Plate is a three-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (fro...

Wing Fixing Plate is a two-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (front...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Washer is a large plain flat washer used as a general-purpose load-spreading fastening component, sized for M6 fixings with a wider outside diamete...

Spare Wheel Buffer for a bonnet-mounted spare wheel. This moulded rubber buffer fits to the bonnet panel and bears against the back of the spare wh...

Door Bottom Seal for the front door. This rubber seal fits along the lower edge of the door, closing the gap between the door bottom and the body t...

Door Seal - Bottom for the left-hand front door, forming part of the door-aperture weather sealing. The seal fits along the lower edge of the door...

Bonnet Buffer is a resilient rubber cushion that forms part of the bonnet closure assembly at the front of the body. It provides the stop the bonn...

Badge Tape - a self-adhesive vinyl body tape forming part of the factory exterior decal and trim scheme. Supplied as an 83 cm length, it bonds dir...