Products

Clutch Master Cylinder Copper Washer for the hydraulic clutch system. Copper sealing washer used at the adaptor connection between the clutch hydr...

Timing Chain Tensioner Spring for Land Rover 2.0L Diesel and 2.25L Petrol and Diesel four-cylinder engines. This spring applies constant pressure ...

Selector Shaft for the Series I, II, IIA, and III transfer case. This shaft is part of the transfer case gear-selection mechanism, transmitting th...

Joint Washer for the gearbox output shaft housing. This gasket seals the mating face between the output shaft housing and the gearbox casing, prev...

Collar Bush for the four-wheel-drive selector mechanism in the two-speed transfer box. It seats on the high-range 4WD selector rod, locating the s...

Use 251323

Plunger for the transfer box selector mechanism. Locates within the transfer selector assembly to provide positive engagement and detenting of tra...

Crankshaft Key locates the timing gear and crankshaft pulley on the crankshaft nose, fixing their angular position relative to the shaft. It trans...

Sealing Washer for the carburettor choke switch on petrol engine applications. Fitted at the choke switch, it seals the joint at the fitting to pr...

Mud Shield for the differential pinion. This pressed shield fits over the differential drive flange, ahead of the pinion oil seal, protecting the ...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

Gearbox Mainshaft Oil Seal for the rear of the manual gearbox, sealing the mainshaft where it passes through the rear of the mainshaft-and-gears se...

Mudshield Output Shaft

Bolt, 7/16" BSF x 1-3/8" secures the upper swivel pin to the swivel housing in the front axle assembly. The top swivel pin retains the swivel ball...

Warning Light - Red for the dashboard instrument panel. Lucas WL3 type red panel warning light indicator, used on classic Land Rover dashboards as...

Cone Bearing - Swivel Housing for the front axle swivel pin assembly. Sits within the swivel housing to support the swivel pin on early Series Lan...

Swivel Pin

Exhaust Bracket for the exhaust system mounting. The bracket secures and locates the exhaust pipework against the underbody, supporting the system...

Spring Road Front SWB 9lf DS

Top Swivel Pin Bearing Spring, part of the front axle swivel pin housing assembly. The spring acts on the top swivel pin bearing to maintain beari...

spring road front SWB 9 leaf Passenger Side

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Wheel Cylinder for the rear drum brake assembly, right-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hy...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Wheel brake cylinder LH

Wheel brake cylinder RH

Seal Ring - a copper crush-type sealing washer. It fits beneath a threaded plug or at a metal-to-metal joint and deforms as it is tightened, takin...

Sump Plug Washer - copper sealing washer for the sump drain plug and thermostat housing on petrol and early diesel engines. The copper washer seat...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Oil Pump O-Ring, a seal within the engine oil pump assembly. The O-ring seals the oil pump strainer (pickup) joint, maintaining the suction seal s...

Main Starter Spring is the principal return spring within the starter motor assembly used on Series I, II, IIA, and III vehicles. It operates withi...

Camshaft Cover Gasket seals the camshaft cover plate to the cylinder block, forming part of the camshaft housing and engine lubrication boundary. ...

Set Screw - Water Pump Spindle is a locking fastener that locates the water pump spindle within the water pump housing on Series engines produced b...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Threaded 7/16 UNF with a 7/8 in shank length, the bolt clamps the flywhe...

Manifold Stud is used to secure the combined inlet/exhaust manifold assembly to the cylinder block on Series vehicles fitted with the 2.25L diesel ...

Banjo Bolt for the timing chain tensioner hydraulic oil feed on Land Rover 2¼ Litre and 2.0 Litre diesel engines. The banjo bolt is a hollow faste...

Rocker Cover Stud for the cylinder head on early Land Rover 4-cylinder engines. The rocker cover stud is a threaded fastener installed into the cy...

Rocker Cover Washer used at the rocker (valve) cover fixing on the cylinder head. Fitted beneath the rocker cover retaining nut, the washer seals ...

Rocker Bush for the rocker shaft assembly in the Defender's 2.5L diesel engine. Fitted to the rocker shaft to support the rocker arms and maintain...