Products

Cylinder Head Bolt is the short-length head bolt that clamps the cylinder head to the block on the 2.25L and 2.5L 4-cylinder petrol engines. The h...

Leaf Spring - LWB - Rear - Drivers Side

Leaf Spring is the rear passenger-side leaf spring for long-wheelbase (LWB) chassis, of 8+2 leaf construction. Land Rover lists it as the left-hand...

Bowl Washer is the sealing joint washer for the fuel sediment bowl (sedimentor) in the fuel system. It seals the bowl to its housing, maintaining ...

Flat Washer with a 3/8" bore, fitted under a bolt head or nut to spread the clamping load over a wider area and protect the mating surface.

Lock Washer fitted under a nut or bolt head to lock a threaded fastening against loosening. Its sprung form bears against the joint face and the u...

Stekker 7-polig Pvc

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Hinge Pin - the pivot pin for the top hatch (windscreen) hinge. It passes through the hinge knuckles to retain the two halves of the hinge while a...

Panel Rivet - a round-head solid rivet for body panel fixing. Used to join body panels and brackets, it has a domed (round) head, a 3/16 in shank ...

Washer

Spiralok Nut for body panel and interior trim fixings. This spring-steel speed nut (clip nut) clips to a panel flange or through a mounting hole a...

Rivet, semi-tubular with a semi-round (truss) head, 3/16 in diameter and 3/8 in long. It secures door weatherstrip and seals to the body aperture....

Chain Bracket Series/Lw

Clevis Pin for the tailboard assembly at the rear of the body. It secures the drop-down tailboard's support cable or chain to its anchor bracket, ...

Centre Squab Buffer - a rubber buffer that cushions the centre seat squab (backrest) against the surrounding bodywork. It prevents metal-to-metal ...

Rope Hook - a securing hook for the canvas hood (soft top). It provides an anchor point around which the hood tie-down rope is passed, holding the...

Ignition Switch Knob - the rotary knob for the PRS-type combined ignition and lighting selection switch. It fits onto the switch spindle to provid...

Floor Panel Screw x 100

Upper Tailgate Lock Cap for the rear end door handle assembly. This small plastic cap fits over the end of the upper tailgate handle, covering and...

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...

Transfer Box to Gearbox Mounting Stud, 2" length, used to fasten the transfer case to the rear of the main gearbox casing. This stud forms part of...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Door Top Glass Retainer for the front door glazing assembly of Series Land Rovers. This retainer secures the top edge of the fixed front door wind...

Rear Side Skin - Left Hand Side for the rear body assembly of Series Land Rovers with the 88" wheelbase. This outer body panel forms the lower rea...

Mudshield for the right-hand side of the vehicle. This panel mounts within the inner wing and wheel arch area to deflect road spray, mud and debri...

Hoodstick - a structural bow forming part of the soft-top canvas roof framework on Land Rover vehicles. This hoodstick is a component of the hood ...

Bulkhead Vent Seal - rubber seal for the bulkhead fresh-air vent flap. This rubber seal fits around the bulkhead air vent aperture, sealing the hi...

Door Hinge Bolt

Door Hinge Spring for the rear door hinge assembly. Return spring fitted within the rear end door hinge on station wagon body variants. Provides t...

Locker Door Hinge

Keep your Land Rovers interior clean and tidy with a loadspace mat. Ribbed rubber / 1,560 x 920 x 3mm Defender 110 - excluded 3 door commercial ...

Seat Squab Bolt - shouldered bolt for mounting the seat squab (backrest) to its frame. This shouldered bolt secures the seat squab at its mounting...

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Aluminium Corner Strip - the curved top retainer for the rear door glass. One of the aluminium retainers in the rear (end) door glazing set, this ...

109 stawag B/C post one-piece door seal LH + RH

Corner capping LH S3 galvanised

Rear Door Side Seal - Right Hand Side for the rear body of the 109" Station Wagon. This rubber seal runs along the side edge of the right-hand rea...