Products

Reverse Gear Selector Detent Spring for the manual gearbox selector mechanism. The spring loads the detent ball against the reverse selector shaft...

Leaf Spring for the rear suspension, right-hand side, within the rear axle and chassis suspension assembly. This multi-leaf spring pack is a seven...

Leaf Spring - a seven-leaf semi-elliptic spring for the rear suspension, passenger side. Mounted between the chassis and the rear axle, it support...

Exhaust Silencer for right-hand-drive applications, constructed in stainless steel. Part of the exhaust system, this silencer attenuates combustio...

Battery Retaining Rod secures the battery into its tray. The threaded rod hooks onto the battery tray and draws the hold-down clamp down against t...

Fan Belt for the engine auxiliary (accessory) drive. Transmits drive from the crankshaft pulley to the water pump, cooling fan and dynamo or altern...

Fuel pump diesel 2.25

Injector Pipe No.3, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Injector Bolt - the banjo bolt at the injector spill-return (leak-off) union. It clamps the leak-off pipe fitting to the top of the injector, its ...

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Radiator Overflow Bottle fitted to the cooling system on Series II, Series III, and 101 Forward Control Land Rovers. This plastic reservoir collec...

Brake Pedal Pivot Bush for the brake pedal assembly. It seats in the pedal box and forms the bearing surface on which the brake pedal pivots on it...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Distributor Cap mounts at the top of the distributor in the ignition system and carries the segment contacts that route high-tension voltage to the...

Water Temperature Sender threads into the cooling system and measures engine coolant temperature, feeding the signal to the dashboard temperature g...

Push Rod for the 2.6L 6-cylinder petrol engine fitted to Series II, IIA, and III Land Rovers. This push rod operates within the valvetrain of the ...

Valve Guide A precision sleeve pressed into the cylinder head that supports and locates the inlet valve stem, holding the valve concentric with its...

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Inlet Valve Guide for the diesel cylinder head, part of the valve train. Pressed into the cylinder head, the guide locates the inlet valve stem an...

Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...

Alternator Pulley mounts on the alternator drive shaft and is turned by the engine drive belt. It transfers rotation from the crankshaft belt driv...

Radiator Drain Plug seals the drain point in the cooling system and is removed to drain coolant during flushing or servicing. When fitted it close...

Brake Pedal Return Spring for the pedal box assembly, fitted to servo-assisted braking systems. The spring returns the brake pedal to its rest pos...

Brake Pipe

Cable Clip for securing wiring harnesses and cables in Land Rover vehicles. Sold individually.

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Needle Roller Bearing - LT95

Gearbox Thrust Washer for the LT95 transmission. This washer sets and controls shaft endfloat within the gearbox, carrying axial loads between the...

Mainshaft Bearing for the manual gearbox. This bearing supports the gearbox mainshaft, locating it within the casing and carrying the radial loads...

Snap Ring used within the LT95 4-speed gearbox to retain the inner member to the mainshaft. The LT95 is the 4-speed gearbox with integral transfer ...

Oil Seal for the LT95 four-speed gearbox, retaining lubricant within the gearbox and transfer casing. It runs against a rotating shaft to keep gea...

Circlip is a split retaining ring that locates on the reverse shaft of the LT95 gearbox. It seats into a machined groove to axially retain the rev...

Spring Pin for the LT95 four-speed gearbox, used in the gear selector mechanism. The hollow, sprung roll pin locates and retains selector componen...

Bronze Distance Piece Mainshaft 1954-71

Bush

Clutch cover assembly designed for Land Rover Series II and Series IIA vehicles with the 2.25 petrol engine. This component forms part of the clut...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Washer

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Front Housing Gasket for the LT95 four-speed gearbox fitted to V8 engines. It seals the joint between the gearbox front housing and the main casin...

Oil Seal for the transfer section of the LT95 combined gearbox and transfer unit, sealing the rear mainshaft. It runs on the rear mainshaft where ...

Gearbox Gasket for the LT95 four-speed gearbox, sealing the power take-off (PTO) cover joint. Fits between the PTO cover and the gearbox main casi...