Products

Gasket

Vacuum Actuator O-Ring for the LT95 4-speed gearbox. This O-ring seals the vacuum actuator fitted to the LT95 transfer case mechanism, used on V8-p...

Brake Light Switch for the pedal box. It closes the stop-lamp circuit when the brake pedal is applied, switching on the brake lights. Used on brak...

Bulb, 12V 4W (type 233, BA9s single-contact bayonet cap). A miniature bayonet bulb used in number plate, side, interior and rear lamp positions.

Bulb, 12V 4W (type 233, BA9s single-contact bayonet cap), supplied as a twin blister pack of two bulbs. A miniature bayonet bulb used in number pla...

Column Stalk Switch mounted on the steering column, combining three controls in a single stalk: the turn-signal (indicator) switch, the horn push a...

Fuse box

Main Wiring Loom for the petrol vehicle electrical system, forming the central harness of the vehicle. This loom carries the principal electrical ...

Selector Cover Gasket - LT95

Location Pin

Clutch Cover is the pressure plate assembly of the manual transmission clutch, for V8 petrol applications. It bolts to the engine flywheel and cla...

Lock Stop Bolt, Front Axle sets the steering lock stop on the front axle. Its head contacts the stop face on the axle to limit swivel travel, cappi...

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...

Clutch Lever Pivot Pin for the LT76 gearbox bellhousing. It forms the pivot about which the clutch release lever rotates when the clutch pedal is o...

Gasket for the front cover of the LT67 gearbox. Seals the front cover plate against the front face of the gearbox housing, preventing transmission...

Mainshaft for the LT76 four-speed manual gearbox. The mainshaft is the gearbox output shaft, carrying the main gear cluster and transmitting drive ...

First Gear Bush for the LT76 gearbox mainshaft. The bush journals the mainshaft first gear, providing the running surface on which the gear turns o...

Clutch push rod

Rear Halfshaft for the Salisbury rear axle, 24-spline, right-hand side. The halfshaft transmits drive from the differential through the axle casin...

Rear Halfshaft for the Salisbury rear axle, 24-spline, left-hand side. The halfshaft transmits drive from the differential through the axle casing...

Bolt

Upper Brake Pipe for right-hand-drive applications, part of the braking hydraulic circuit. This rigid metal pipe carries pressurised hydraulic flu...

Ignition Switch for the steering-column lock, diesel specification. The switch is the electrical unit that fits into the steering-column lock barre...

Ignition Switch - Petrol - Steering Column is the electrical ignition and starter switch mounted in the steering column, forming part of the igniti...

Light Socket for the inspection lamp on Series Land Rover vehicles. This black bayonet-type bulb holder is used in the inspection lamp assembly, p...

Hose

107.5cm long 0.13cm thick

Core Plug for the engine casting. Core plugs seal the core holes left in the cylinder block after the casting sand is removed during manufacture. ...

Series 3 Engine Harness. 2.25 Litre 4-cylinder petrol and 2.6 Litre 6-cylinder petrol with Choke Thermostat Warning Switch

Stop/Tail Lens is the replaceable coloured lens for the rear stop and tail lamp assembly. It fits over the large 3 inch (76 mm) round lamp body, s...

Clutch Slave Cylinder is the hydraulic actuator in the clutch release circuit, mounted externally on the gearbox bellhousing. When the clutch peda...

Front Propeller Shaft for the 109" 1-ton Series Land Rover, transmitting drive from the transfer box to the front axle. This propeller shaft runs ...

Spring pin

Low Range Gear

U-Bolt for the rear leaf-spring suspension of long-wheelbase (LWB) models. The U-shaped bolt passes over the axle and clamps the rear leaf-spring ...