Products

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

Automatic Gearbox Sump Plug - the threaded plug that seals the drain point on the ZF automatic transmission oil pan. Removed to drain the transmis...

Automatic Gearbox Sump Plug - the threaded plug that seals the drain point on the ZF automatic transmission oil pan. Removed to drain the transmis...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

Layshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...

Layshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...

Sealing Washer seals the engine oil sump drain plug, fitting between the drain plug head and the sump drain boss. When the drain plug is tightened...

Sump Plug for the engine oil sump drain. Fitted to the sump drain port and removed at each oil change to drain the engine oil. The sealing washer ...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Intermediate shaft lock nut LT230

joint washer, various applications, mostly BMW engines. L322 - Oil Pan/Oil Level Indicator M62 B44 4.4 V8 Petrol L322 - Oil Pan/Oil Level Indicato...

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Secondary Air Injection Solenoid Valve for the secondary air injection system on 4.0L and 4.6L V8 EFI petrol engines. The solenoid is energised by...

Exhaust Downpipe for the V8 petrol engine, incorporating a catalytic converter and forming the front section of the exhaust system. The downpipe c...

Intermediate Exhaust Silencer with Catalyst - the centre section of the exhaust system on 4.0L and 4.6L V8 petrol applications. It sits between th...

Exhaust Tailpipe Assembly - the rear-most section of a single-pipe exhaust system. The assembly carries exhaust gas from the rear silencer outlet ...

Exhaust tailpipe silencer P38 dual LH

Exhaust Tailpipe Silencer for the right-hand side of a twin (dual) exhaust system. Forms the rearmost section of the exhaust, attenuating gas-flow ...

Locking Washer

Fuel Pump for the V8 petrol fuel delivery system. Mounted in the fuel tank, the pump draws fuel from the tank and delivers it under pressure throu...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Repair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...

Fuel Filter Assembly within the diesel fuel supply circuit, removing contaminants from the fuel before it reaches the injection system. Installed ...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Fuel Filler Cap that seals the fuel tank filler neck. Non-locking type with a black finish, closing the filler neck against fuel vapour loss and t...

Fuel Filler Cap seals the fuel tank filler neck within the fuel storage system. It closes the filler neck to retain fuel vapour, maintain the corr...

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Headlamp assy LH

Front Indicator Lamp - Clear Glass, Right-Hand Side. Clear-lens front direction indicator unit for European and export markets (excluding North Ame...

Front Indicator Lamp for the front exterior lighting assembly, mounted on the left-hand side of the vehicle. The lamp provides front direction-ind...

HOLDER - BULB - SINGLE POLE - D1/D2/DEF ALL/F1/P38

Bulb Holder - double-filament bulb holder for an exterior lamp assembly, accepting a 5/21W (P21/5W) twin-filament bulb. The holder seats into the ...

H1 Halogen Bulb - 55 W single-filament halogen capsule on the standard P14.5s base, used in the front fog lamp and in headlamp reflectors built aro...