Products

Contact Set - Lucas Distributor is the breaker-point set for the ignition distributor. Mounted on the distributor baseplate, the points are opened...

Voltage Regulator for the dynamo charging circuit – the Lucas RB340 control box. Wired between the C40 dynamo and the battery, the control box reg...

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Shock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...

Shock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...

Shock Absorber - Oil Filled - Front for the front suspension assembly on Series I, II, and IIA Land Rovers. This oil-filled hydraulic unit mounts ...

Shock Absorber for the rear axle, damping suspension movement by converting the energy of spring oscillation into heat as the axle moves relative t...

Shock Absorbers for the rear axle, supplied as a matched pair. Each damper controls suspension movement by converting the energy of spring oscillat...

Shock Absorber for the rear axle, damping suspension movement by converting the energy of spring oscillation into heat as the axle moves relative t...

Shock Absorber for the front suspension - an oil-filled, heavy-duty hydraulic damper. Mounted between the axle and the chassis, it damps the oscil...

Shock Absorber for the front suspension - an oil-filled, heavy-duty hydraulic damper. Mounted between the axle and the chassis, it damps the oscil...

Glass Fuse - 25A - a 25 A glass cartridge fuse for the vehicle's electrical circuits. The glass body carries a calibrated wire element between two...

7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...

Crystal Headlamp - a matched pair of 7-inch round crystal halogen headlamps for right-hand-drive applications. The clear (crystal) lens and facete...

7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...

Starter Switch for Land Rover Series 1 and Series 2 models (1948-1966). This switch activates the starter solenoid to engage the starter motor whe...

Alternator - charging unit in the vehicle's electrical charging system. Driven from the engine by the accessory belt, it generates current to powe...

Lucar Connector - a fully insulated two-way in-line electrical connector for joining wiring within the loom. Of the Lucar (blade) terminal type, i...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Rotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...

Overdrive Needle Bearing for the front of the mainshaft in a Fairey overdrive unit. The bearing supports the overdrive clutch sleeve on the mainsh...

Washer fits the clutch cross shaft within the clutch release mechanism. It seats on the clutch cross shaft pin, retaining the pin and setting its ...

Workshop Manual covering the Land Rover Series 1, 1948 to 1958, in both petrol and diesel forms. The manual sets out repair and overhaul procedure...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Bolt, 1/4" BSF x 1", serving as the steering lockstop in the front axle steering assembly. The bolt threads into the swivel housing and is set to l...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Bolt - a small-diameter bolt with a 2BA (British Association) thread and a 5/8" length. Used as a light-duty fixing for small fittings and electric...

Pipe clamp 109" intermediate exhaust pipe centre bracket (For the bottom bracket use 264889.)

Exhaust Valve - the poppet valve that seals the exhaust port in the cylinder head and opens on the exhaust stroke to release spent combustion gases...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Front Propshaft for the 4-cylinder 2.25L petrol driveline. It transmits drive from the transfer box front output to the front axle differential, de...

Interior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...

Light socket red

Rear Propshaft for the long-wheelbase chassis, transmitting drive from the transfer box output flange to the rear axle input within the driveline. ...

Manifold Stud is an M8 x 65 mm threaded stud that secures the inlet and exhaust manifold to the cylinder head on the four-cylinder petrol engine. ...

Anti-Roll Bar Link & Shock Bush Kit renews the compliant mounting bushes in the anti-roll bar link and shock absorber mounting points within th...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...