Products

Transfer Box to Gearbox Mounting Stud, 2" length, used to fasten the transfer case to the rear of the main gearbox casing. This stud forms part of...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Front Floorplate - Right-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the right-ha...

Front Floorplate - Left-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the left-hand...

Upper Door Hinge for the right-hand door, forming the upper pivot of the door-to-body mounting. Fitted as the upper member of the door's two-hinge...

Door Cap (Galvanised, Right-Hand) is the capping rail that forms the top edge of the right-hand front door frame around the window aperture. The g...

Door Cap (Galvanised, Left-Hand) is the capping rail that forms the top edge of the left-hand front door frame around the window aperture. The gal...

Rubber Buffer for the door-top sliding side window. The buffer fits at the top of the door and acts as an end-stop for the sliding glass, limiting...

Door Top Seal Strip for the front door assembly. This rubber seal runs along the upper section of the door frame, sealing the gap between the door ...

Door Top Glass Retainer for the front door glazing assembly of Series Land Rovers. This retainer secures the top edge of the fixed front door wind...

Filler Strip for the door top. The strip fits along the top edge of the door, closing and finishing the joint at the door-top glass frame and seal...

Filler Strip Spacer for the door top, fitting at the vertical joint of the door-top glass frame. The strip fills and finishes the vertical gap in ...

Rear Side Skin - Left Hand Side for the rear body assembly of Series Land Rovers with the 88" wheelbase. This outer body panel forms the lower rea...

Wing Stay for the rear body structure of the Series Land Rover. This right-hand steel bracket braces the rear wing to the body sill, providing str...

Sill Panel (5" Deep, Front, Right-Hand) is the lower body panel that runs along the right-hand front body side beneath the door aperture. It forms...

Sill Panel (5" Deep, Front, Left-Hand) is the lower body panel that runs along the left-hand front body side beneath the door aperture. It forms t...

Sill Panel (5" Deep, Rear, Right-Hand) is the lower body panel that runs along the right-hand rear body side beneath the rear body aperture. It fo...

Sill Panel (5" Deep, Rear, Left-Hand) is the lower body panel that runs along the left-hand rear body side beneath the rear body aperture. It form...

Handbrake Gaiter - round-hole type - for the transmission handbrake (parking brake) lever assembly. This rubber gaiter fits over the base of the L...

Tailgate Chain Cover - a pair of protective sleeves that fit over the two retaining chains supporting the rear tailgate. Each chain links the tail...

Wing Panel (Aluminium, Front Outer, Right-Hand) is the outer front body panel covering the right-hand front wheel arch. It forms the visible body ...

Front Outer Wing Panel - Aluminium - Left Hand Side for Series Land Rovers. This aluminium outer wing panel replaces the front left wing skin on S...

Mudshield for the right-hand side of the vehicle. This panel mounts within the inner wing and wheel arch area to deflect road spray, mud and debri...

Front Mudshield - RHD - Left Hand Side for Series II and IIA Land Rovers. This inner panel sits between the front wing and the engine bay on the l...

Steering Box Cover for the steering box, for right-hand-drive (RHD) applications. The cover plate bolts onto the steering box housing, enclosing a...

Steering Box Cover - LHD - inner wing mudshield for the steering box. This pressed cover fits over the steering box on the inner wing panel, shiel...

Hoodstick - front bow of the soft-top hood frame. This steel bow forms the front arch of the soft-top hood frame, providing structural support at ...

Hoodstick - the rearmost bow of the soft-top canvas roof framework on Land Rover Series and Defender vehicles. This hoodstick forms the rear struc...

Hoodstick - a structural bow forming part of the soft-top canvas roof framework on Land Rover vehicles. This hoodstick is a component of the hood ...

Hook for the soft top retaining rope, part of the hood and hoodstick assembly. Secures the rope that runs along the soft top drain channels.

Front Rope Retaining Hook - Left Hand Side for the soft-top hood system on Series and Defender Land Rovers. This hook is part of the hoodstick and...

Bulkhead Vent Seal - rubber seal for the bulkhead fresh-air vent flap. This rubber seal fits around the bulkhead air vent aperture, sealing the hi...

Bulkhead Vent Seal - rubber seal for the bulkhead fresh-air vent flap. This rubber seal fits around the bulkhead air vent aperture, sealing the hi...

Sliding Window Seal for the front door assembly. This rubber seal fits to the front face of the sliding side window, sealing the glass against the ...

Window Channel for the front door sliding side window assembly. This aluminium channel runs along the front face of the sliding window and retains...

Cab Mounting Stud

Tie Tube - a side brace for the full-length soft-top hood frame assembly on long-wheelbase Land Rover vehicles. This tube provides lateral structu...

Door Hinge Bolt

Hinge Pin Kit containing the replacement hardware for door and rear tailgate hinges on Series and early Defender models. Fits the front and rear d...

Door Hinge Spring for the rear door hinge assembly. Return spring fitted within the rear end door hinge on station wagon body variants. Provides t...

Locker Door Hinge

Hood Stick Kit - the framework of bows and sticks that forms the skeleton of a canvas soft top (tilt), carrying and tensioning the fabric over the ...

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...