Products

Bolt - Spare Wheel Bonnet Mounting for Land Rover Series I, II, IIA, and III models fitted with a bonnet-mounted spare wheel carrier. This clamp b...

Headlamp Guard in galvanised steel. A protective grille fitted over the headlamp lens to shield it from stone chips, debris and impact damage. The...

Headlamp Guard in moulded plastic. A protective guard fitted over the headlamp lens to shield it from stone chips, debris and impact damage. Suppl...

Radiator Grille mounts in the front body panel aperture, ahead of the radiator, admitting cooling airflow to the core while protecting it from road...

Air Vent Mechanism - operating mechanism for the dash-mounted fresh-air ventilator. Controls the opening and closing of the bulkhead air vent flap...

Decal – Dash is an adhesive instrument switch-tab label for the dashboard control panel. It is applied to the face of a plastic switch tab to iden...

Demister Tube Grommet is a moulded rubber grommet in the windscreen demister ducting that seals the demister hose where it passes through the lower...

Bonnet Hinge Bush for the Land Rover bonnet hinge assembly. This bush fits into the bore of the bonnet hinge, providing a wear surface around the ...

Door Check Arm Bracket is the pivot bracket in the door check assembly that anchors the check arm to the body at the rear door. The check arm runs...

Retainer - LH

Heater Air Intake Trim fits the front wing air intake of the heating and ventilation system. It finishes the fresh-air intake aperture in the wing...

Blanking Plug for the instrument panel, fitted to close an unused aperture in the dashboard where an instrument, switch or gauge is not installed. ...

Hose Clip Spring is the spring connector clip for the heater demister and air outlet pipes. Retains the demister ducting and outlet flaps within t...

Windscreen Hinge Bolt is a fixing used to secure the folding windscreen frame hinge to the scuttle. It clamps the hinge mounting at the base of th...

Heater Intake Hose is the flexible convoluted air hose in the heater fresh-air intake ducting. It connects the fresh-air intake to the heater hous...

Rear Sill Panel for the right-hand side of the body understructure on long wheelbase (109 inch) models. Fitted at the rear sill position, this pane...

Sill Panel Rear 109 Not Station Wagon - LH

Sliding Window Catch for the front door sliding window assembly on Series Land Rover models. This black plastic catch secures the sliding window p...

Door Hinge Shim for the Land Rover door hinge assembly. This 1mm shim is fitted between the door hinge and its mounting face to set or adjust the ...

Bracket

Spare Wheel Bracket is the mounting bracket for a side-mounted spare wheel. Forms part of the side spare wheel carrier, working with the anchor pl...

Replace or upgrade the front outer wing panel on your Series 2/3 Land Rover with this aluminium panel designed for Right-Hand Side (RHS) and Left-H...

Front outer wing RH SIII plastic

Outer Wing Panel for the left-hand side, manufactured in aluminium. The outer wing forms the front body panel covering the wheel arch and bolts to...

Window Channel - Lower is the lower glass-run channel for the front door window. It runs along the bottom of the window aperture and guides the do...

Window Channel, 26.5 in (673 mm), a felt-lined glass run channel for the rear body side sliding windows. The glass slides within the channel, whic...

Window Catch Gasket seals the window catch on the rear side door. It fits between the window catch and the door panel, forming a weatherproof seal...

Steering Column Cover is the upper shroud enclosing the steering column. Fits together with the lower shroud 347558 to conceal the column and swit...

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...

Shim door GENUINE - door striker plate 1958 - 1984 - side hinged tailgate

Grille Spring Clip for securing the front grille panel on Series III models. Fitted at the grille mounting points, this spring clip retains the fro...

Demister Tube

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Radiator Panel for the front-end assembly on Series III models. This panel forms the surround and support structure for the radiator, integrating w...

Window Channel

Window Channel

Window Channel - Vertical - the upright glass run for the Truck Cab side window, part of the door glazing assembly. It lines the vertical edge of ...

Window Channel - Top is the upper glass-run channel that guides the top edge of the window glass, supplied as a 94 cm length. It forms the running...

Window Catch Mask fits behind the window catch on the rear side door. This plate seats between the catch and the door skin, masking and reinforcin...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Key Features & Benefits: Color: Black Fitment: Suitable for Land Rover Series models Standard Design: Non-adjustable seat base offering s...

Seat Frame for the adjustable driver's seat on Series II and Series III models. This structural frame forms the base of the driver's seat assembly.

Bullet Connector, single-sleeve, one-way. Accepts a standard bullet terminal and is used throughout Land Rover wiring harnesses for individual wire...

Selector Detent Spring is part of the gearbox gear-selection detent for the forward-gear selector shafts (1st/2nd and 3rd/4th). It loads the deten...

Flywheel Housing Stud secures the flywheel housing to the rear of the cylinder block on the 2.0L petrol engine. The stud provides a threaded fixin...