Products

Small Gasket for 269974

Sealing Washer - copper sealing ring for the cooling system drain points. It seats under the radiator drain plug and the cylinder block drain tap, ...

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Track Rod Retainer for the Series Land Rover steering system. This retainer secures the protective rubber gaiter at the track rod end, holding it ...

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Driving Member Bolt for the axle driving member assembly. This 3/8" BSF x 1-19/32" bolt retains the driving member to the hub assembly. The drivin...

Bolt with Whitworth (BSW) thread - 1/4 inch diameter, 1-1/4 inch length, sold individually. Used across Series Land Rover applications requiring t...

Brake Clevis A clevis for the brake drum expander mechanism within the drum braking system. It forms the pinned link between the brake operating r...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Copper Sealing Washer, 7/16 inch, for hydraulic pipe unions on Series Land Rovers. This annealed copper washer seats under a banjo bolt or pipe un...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Wheel Nut for the road wheel and hub assembly, securing the road wheel onto the hub studs. The double-chamfer design is tapered at both ends, so t...

Oil seal

Axle casing oil seal

Gear Change Selector Shaft Spring A spring for the gearbox gear-change selector mechanism. It acts on the selector shaft to provide the spring loa...

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Mainshaft Nut for the LT76 gearbox, fitted to the mainshaft and gear assembly. It retains the gear cluster on the mainshaft, clamping the stack ag...

Output shaft bearing

Pinion Bearing Retaining Plate for the Power Take-Off (PTO) unit on Series Land Rovers. This retaining plate locates and secures the pinion bearin...

Circlip - Rear Mainshaft Bearing for the Series Land Rover gearbox. This circlip retains the rear mainshaft bearing within the gearbox casing, pre...

External Circlip - retaining circlip fitted within the LT67 main gearbox. Seats in a shaft groove to axially locate a gear, bearing or spacer on i...

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

PTO Selector Cover Plate - a blanking plate for the power take-off (PTO) selector aperture on the transfer box. It covers and seals the selector o...

Handbrake Stud A mounting stud for the transmission (drum) handbrake within the braking system. It secures the transmission brake back plate to th...

Stud for use in Land Rover gearbox assembly.

Transfer Box Gear - High is the high range gear wheel in the Land Rover Series transfer box assembly, fitting Series vehicles from 1948 to 1984. T...

Transfer Box Mainshaft is the central rotating shaft within the transfer box assembly, running through the gear train and transmitting drive betwee...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Starting Handle for manual cranking of the engine. The handle engages the dog on the front of the crankshaft, allowing the crankshaft to be turned...

Brake Shoe Spring for the drum brake assembly on Land Rover vehicles. This return spring pulls the brake shoes back from the drum face after each ...

Drive Shaft Hub Cap for the hub assembly on Land Rover Series vehicles. This cap fits at the outer face of the hub, closing off the drive shaft en...

Transfer Case Intermediate Gear with a 44/22 tooth configuration, operating within the transfer box gear train. The intermediate gear meshes with ...

Transfer Lever Knob in red, for the high/low range selector on the transfer gearbox. It threads onto the top of the transfer change lever and prov...

Inner Pinion Bearing for the Land Rover Series axle differential, supporting the pinion shaft at the inboard (crown wheel) end within the different...

Gear Lever Bracket - mounting bracket for the gear change lever on the LT76 gearbox. The gear lever pivots in the bracket, locating the lever over...

Gear Lever Housing The ball/socket housing for the main gear lever, mounted on the gearbox top cover (turret). It seats the spherical lower end of...

Gear Lever Retaining Plate for the gear lever turret on the LT76 manual gearbox. The plate bolts over the base of the gear lever to retain it in i...

Gear Lever Retaining Spring The spring that retains the main gear lever in its ball housing on the gearbox top cover. It bears down on the lever's...

Oil Seal - Clutch Withdrawal Sleeve for the Land Rover Series 2A gearbox, specifically the partially synchronised variant fitted with a sealed clut...

Circlip - Gear Lever Spring Retention for the Series Land Rover gearbox gear lever assembly. This circlip retains the spring, retaining plate and ...