Products

Radiator Overflow Hose carries coolant overflow away from the radiator filler neck. It connects to the overflow spigot on the radiator filler neck...

Expansion Tank Hose connects the coolant expansion (header) tank into the cooling circuit. It carries coolant between the expansion tank and the r...

Brake Pedal Pivot Bush for the brake pedal assembly. It seats in the pedal box and forms the bearing surface on which the brake pedal pivots on it...

Joint Washer for the radiator cap, part of the engine cooling system. This sealing washer seats between the radiator cap and the filler neck, main...

Brake pipe

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the carburettor throttle spindle. Transmits pedal movement ...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Spark Plug for low-compression (7:1) petrol engines fitted with screened ignition on 24V FFR (Fitted For Radio) vehicles. The screened design supp...

Flywheel assy

Distributor Cap mounts at the top of the distributor in the ignition system and carries the segment contacts that route high-tension voltage to the...

Distributor Cap mounts at the top of the distributor in the ignition system and carries the segment contacts that route high-tension voltage to the...

Heater Control Pin

Water Temperature Sender threads into the cooling system and measures engine coolant temperature, feeding the signal to the dashboard temperature g...

Water seal

Crankshaft Timing Sprocket mounts on the nose of the crankshaft and forms part of the timing drive. Its teeth engage the timing chain to drive the...

Glow Plug (cold-start heater plug) threaded into the cylinder head, part of the diesel cold-start heating circuit. The heated tip projects into th...

Flywheel Ring Gear (starter ring gear) for the diesel flywheel, part of the clutch and flywheel assembly. The toothed ring is fitted around the fl...

Push Rod for the 2.6L 6-cylinder petrol engine fitted to Series II, IIA, and III Land Rovers. This push rod operates within the valvetrain of the ...

Exhaust Stud - Manifold to Front Pipe is a 5/16 UNF threaded stud that secures the exhaust manifold outlet flange to the front pipe in the exhaust ...

Valve Guide A precision sleeve pressed into the cylinder head that supports and locates the inlet valve stem, holding the valve concentric with its...

Valve Guide A precision sleeve pressed into the cylinder head that supports and locates the inlet valve stem, holding the valve concentric with its...

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Inlet Valve Guide for the diesel cylinder head, part of the valve train. Pressed into the cylinder head, the guide locates the inlet valve stem an...

Inlet Valve Guide for the diesel cylinder head, part of the valve train. Pressed into the cylinder head, the guide locates the inlet valve stem an...

Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...

Alternator Pulley mounts on the alternator drive shaft and is turned by the engine drive belt. It transfers rotation from the crankshaft belt driv...

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Trunnion

Front Bumper for the Series II, IIA and III Military Lightweight and Airportable variants, including JC3 specification vehicles. This bumper forms ...

Military fuel cap

Suspension Spring U-Bolt for the front leaf-spring suspension, clamping the axle to the spring pack. The U-bolt wraps around the front axle tube a...

Radiator Drain Plug seals the drain point in the cooling system and is removed to drain coolant during flushing or servicing. When fitted it close...

Heater Hose for the rear of the heater circuit, carrying engine coolant between the heater pipe and the heater unit. This flat-section hose forms ...

Heater Hose for the front of the heater circuit, carrying engine coolant between the engine feed and the heater unit. This flat-section hose forms...

Brake Pedal Return Spring for the pedal box assembly, fitted to servo-assisted braking systems. The spring returns the brake pedal to its rest pos...

Brake master cylinder (single line with servo)

Brake Master Cylinder is the hydraulic control unit of the braking system, generating the fluid pressure that actuates the wheel cylinders at each ...

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Radiator Hose - Top - 2.25 Petrol is the upper coolant hose connecting the thermostat housing outlet to the inlet of the radiator header tank in th...

Bottom radiator hose SII(A) 2.25

Brake Pipe

Cable Clip for securing wiring harnesses and cables in Land Rover vehicles. Sold individually.

Bulb rated 12V 4W with a small-diameter fitting, part of the vehicle lighting system. This low-wattage bulb suits the small-fitting (Lucas-type) l...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...