Products

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Needle Roller Bearing - LT95

Gearbox Thrust Washer for the LT95 transmission. This washer sets and controls shaft endfloat within the gearbox, carrying axial loads between the...

Mainshaft Bearing for the manual gearbox. This bearing supports the gearbox mainshaft, locating it within the casing and carrying the radial loads...

Thrust Bearing for second and third gears in the LT95 four-speed gearbox. This flat Torrington needle roller bearing seats against the 2nd and 3rd...

Snap Ring used within the LT95 4-speed gearbox to retain the inner member to the mainshaft. The LT95 is the 4-speed gearbox with integral transfer ...

Gasket gearbox front cover and oil pump. LT95 4-speed gearbox - Early 110 V8, - S3 109" stage 1 V8, - 101" F.C. - Early Range Rover Classic

Oil Seal for the LT95 four-speed gearbox, retaining lubricant within the gearbox and transfer casing. It runs against a rotating shaft to keep gea...

Circlip is a split retaining ring that locates on the reverse shaft of the LT95 gearbox. It seats into a machined groove to axially retain the rev...

Spring Pin for the LT95 four-speed gearbox, used in the gear selector mechanism. The hollow, sprung roll pin locates and retains selector componen...

Clutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...

Clutch Lever Clip that retains the clutch release lever on its pivot post within the gearbox bellhousing. The clip holds the release fork onto the...

Clutch Cap that closes an aperture in the clutch bellhousing around the release mechanism. Fitted over an opening in the bellhousing, the cap seal...

Oil Seal for the front output shaft of the LT95 gearbox, sealing the transfer case around the rotating output shaft. The LT95 is a combined main g...

Bronze Distance Piece Mainshaft 1954-71

Bush

Clutch cover assembly designed for Land Rover Series II and Series IIA vehicles with the 2.25 petrol engine. This component forms part of the clut...

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

Driving Member is the front hub drive flange that couples the axle halfshaft to the road wheel hub. It bolts to the outer face of the front hub, w...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Washer

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

thrust collar, bush for stub axle - RRclassic upto (VIN) HA610293, - 101" Forward Control.

Front Housing Gasket for the LT95 four-speed gearbox fitted to V8 engines. It seals the joint between the gearbox front housing and the main casin...

Oil Seal for the transfer section of the LT95 combined gearbox and transfer unit, sealing the rear mainshaft. It runs on the rear mainshaft where ...

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

Gearbox Gasket for the LT95 four-speed gearbox, sealing the power take-off (PTO) cover joint. Fits between the PTO cover and the gearbox main casi...

4WD Selector Rod for the Series transfer box. It forms part of the four-wheel-drive engagement linkage, transmitting selector movement through the...

Gasket

Gasket

Washer

Vacuum Actuator O-Ring for the LT95 4-speed gearbox. This O-ring seals the vacuum actuator fitted to the LT95 transfer case mechanism, used on V8-p...

Exhaust Bush - Male is the male-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the cor...

Exhaust Bush - Female is the female-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the...

Fuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...

Inlet Manifold Stud with a UNF thread. Threads into the cylinder head to mount the inlet manifold, taking the manifold nut that clamps the manifol...

Oil Filler Cap Assembly for the rocker (valve) cover of the 2.25L 4-cylinder petrol engine. The cap seals the oil filler neck and incorporates an i...

Coolant Bypass Hose - 2.25 Petrol is the short coolant hose forming the thermostat bypass circuit in the 2.25L Petrol engine cooling system. When ...

Brake Light Switch for the pedal box. It closes the stop-lamp circuit when the brake pedal is applied, switching on the brake lights. Used on brak...