Products

Brake Light Switch for the pedal box. It closes the stop-lamp circuit when the brake pedal is applied, switching on the brake lights. Used on brak...

Brake Light Switch for the pedal box. It closes the stop-lamp circuit when the brake pedal is applied, switching on the brake lights. Used on brak...

Bulb, 12V 4W (type 233, BA9s single-contact bayonet cap). A miniature bayonet bulb used in number plate, side, interior and rear lamp positions.

Bulb, 12V 4W (type 233, BA9s single-contact bayonet cap), supplied as a twin blister pack of two bulbs. A miniature bayonet bulb used in number pla...

Column Stalk Switch mounted on the steering column, combining three controls in a single stalk: the turn-signal (indicator) switch, the horn push a...

Column Stalk Switch mounted on the steering column, combining three controls in a single stalk: the turn-signal (indicator) switch, the horn push a...

Fuse box

Main Wiring Loom for the petrol vehicle electrical system, forming the central harness of the vehicle. This loom carries the principal electrical ...

Wheel Nut, Flat Type secures the road wheel to the hub studs. It has a flat, single-chamfer seating face and a 27mm hexagon.

Clutch Release Fork operates inside the bellhousing as part of the manual transmission clutch release mechanism. Pivoting on its mounting in the c...

Clutch release fork kit used within the manual transmission clutch release mechanism. The release fork operates in the clutch housing and transfers...

Selector Cover Gasket - LT95

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Layshaft Bearing for the early-type LT76 gearbox. It supports the layshaft (countershaft) within the gearbox, carrying the cluster gear that trans...

Gear Lever Knob threads onto the top of the main gearbox gear lever to form the hand grip used for gear selection. It gives the driver a defined c...

Location Pin

Shim 1.65mm for Layshaft Speed - V8 4

Clutch Cover is the pressure plate assembly of the manual transmission clutch, for V8 petrol applications. It bolts to the engine flywheel and cla...

Bolt - BSF - 1-3/8 in is a British Standard Fine (BSF) hex bolt, 1-3/8 in in length, used as a fastener in the front swivel pin housing, rear axle ...

Lock Stop Bolt, Front Axle sets the steering lock stop on the front axle. Its head contacts the stop face on the axle to limit swivel travel, cappi...

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...

Swivel pin & bracket

Layshaft for the LT76 four-speed gearbox, Suffix A only. It carries the cluster of layshaft gears below the mainshaft, driven by the constant-mesh ...

Reverse Selector Fork for the Land Rover Series IIA and Series III 4-speed main gearbox, Suffix A build. This fork engages and disengages reverse ...

Reverse Gear for the LT76 four-speed gearbox, Suffix A only. The reverse idler gear is brought into mesh when reverse is selected, reversing the di...

Clutch Lever Pivot Pin for the LT76 gearbox bellhousing. It forms the pivot about which the clutch release lever rotates when the clutch pedal is o...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Gasket for the front cover of the LT67 gearbox. Seals the front cover plate against the front face of the gearbox housing, preventing transmission...

Mainshaft - Series 3

Mainshaft for the LT76 four-speed manual gearbox. The mainshaft is the gearbox output shaft, carrying the main gear cluster and transmitting drive ...

First Gear Bush for the LT76 gearbox mainshaft. The bush journals the mainshaft first gear, providing the running surface on which the gear turns o...

Thrust Washer

Clutch push rod

Rear Halfshaft for the Salisbury rear axle, 24-spline, right-hand side. The halfshaft transmits drive from the differential through the axle casin...

Rear Halfshaft for the Salisbury rear axle, 24-spline, left-hand side. The halfshaft transmits drive from the differential through the axle casing...

Wheel Stud for the axle hub - 16mm pull-in type. Mounts in the hub flange to carry the road wheel, which is clamped by the wheel nut running on th...

Wheel Hub Assembly - the complete axle hub, supplied with the wheel studs already fitted. It serves both front and rear hub positions. The hub mou...

Layshaft Bearing Distance Piece Spacer for the layshaft (cluster gear) bearing within the main gearbox. It locates against the layshaft bearing to...

Brake Drum - 11 in - Large Wheel Studs is a cast iron drum for the drum brake assemblies of Series 3 and Defender models. The drum measures 11 inc...

Front Brake Drum for the front drum brake assembly. It mounts to the front hub and rotates with the wheel; the brake shoes expand outward against ...