Products

Battery Cover is the top fixing frame of the battery securing assembly. It clamps down over the top of the battery and bolts to the battery tray, h...

Bolt

Heater Hose - S Shape carries coolant from the engine to the heater matrix in the Series III cabin heating circuit. The hose has an S-shaped profi...

Radiator Hose - Top - 2.25L Petrol connects the thermostat housing outlet on the 2.25L Petrol engine to the top inlet of the radiator, forming part...

Radiator - Copper Core sits in the engine cooling circuit, dissipating heat from the coolant to hold a stable operating temperature under load. Th...

Brake Pipe - pre-formed rigid brake pipe forming part of the hydraulic braking circuit. It carries pressurised brake fluid between components of t...

Brake Hose – 1-Ton is the front flexible hose in the front brake hydraulic circuit. It carries fluid from the rigid brake pipe on the chassis to th...

Upper Brake Pipe for right-hand-drive applications, part of the braking hydraulic circuit. This rigid metal pipe carries pressurised hydraulic flu...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Ignition Switch for the steering-column lock, diesel specification. The switch is the electrical unit that fits into the steering-column lock barre...

Ignition Switch - Petrol - Steering Column is the electrical ignition and starter switch mounted in the steering column, forming part of the igniti...

Light Socket for the inspection lamp on Series Land Rover vehicles. This black bayonet-type bulb holder is used in the inspection lamp assembly, p...

Speedometer Cable – LHD is the mechanical drive cable that transmits road speed to the speedometer. The rotating inner core runs inside a protectiv...

Selector Rod Rubber Grommet Washer is the rubber sealing element fitted around the reverse gear selector shaft at its exit point through the Series...

Hose

107.5cm long 0.13cm thick

Core Plug for the engine casting. Core plugs seal the core holes left in the cylinder block after the casting sand is removed during manufacture. ...

Stud for the carburettor-to-inlet-manifold joint. Threaded stud that secures the carburettor onto the inlet manifold flange. It provides the fixin...

Series 3 Engine Harness. 2.25 Litre 4-cylinder petrol and 2.6 Litre 6-cylinder petrol with Choke Thermostat Warning Switch

Side Repeater Lamp - Front is part of the exterior lighting system, mounting in the front wing to give a side-on indication of the direction indica...

switch loss vacuum

Side Lamp Lens

Side Lamp Lens - Front - Clear is the replaceable lens for the front side and indicator lamp within the exterior lighting assembly. The clear lens...

Rear Stop/Tail Light Assembly - the combined rear lamp providing both the tail (running) light and the brake stop light. It carries a dual-filamen...

Stop/Tail Lens is the replaceable coloured lens for the rear stop and tail lamp assembly. It fits over the large 3 inch (76 mm) round lamp body, s...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

pipe clip 1/2" (12.7mm) for 3/8" (9.5mm) hole

Rear brake drum installed in the rear drum brake assembly of the vehicle braking system. The drum mounts to the rear hub and rotates with the wheel...

Clutch Slave Cylinder is the hydraulic actuator in the clutch release circuit, mounted externally on the gearbox bellhousing. When the clutch peda...

Clutch Slave Cylinder is the hydraulic actuator in the clutch release circuit, mounted externally on the gearbox bellhousing. When the clutch peda...

Front Propeller Shaft for the 109" 1-ton Series Land Rover, transmitting drive from the transfer box to the front axle. This propeller shaft runs ...

Gearbox 1st Speed Gear for the LT76 four-speed manual gearbox. This gear provides the first (lowest) forward ratio within the gearbox main gear tr...

2nd Speed Gear for the Series III LT76 4-speed gearbox, Suffix A, B and C builds. This gear is part of the mainshaft gear cluster and meshes with ...

Synchro Cone – LT76 is a synchroniser ring from the synchromesh assembly of the LT76 manual gearbox. It is the friction component that brings the g...

Half Shaft – Rear RH – 10-Spline Short is the rear axle drive shaft for the right-hand side. It carries the drive from the differential out to the ...

Half Shaft – Rear LH – 10-Spline is the rear axle drive shaft for the left-hand side. It transmits drive from the differential out to the rear hub ...

Spring pin

Reverse Shaft for the Series III 4-speed gearbox, Suffix A build. This shaft carries the reverse idler gear within the gearbox casing. It fits the...

Brake Drum - 10 Inch for the wheel brake assembly on early short wheelbase Series Land Rovers. Fits the 10-inch drum brake system used on SWB (88"...

Clutch Plate is the friction-lined driven plate of the clutch assembly, 9 inch (229 mm) diameter. Its splined hub engages the gearbox input shaft ...

Clutch Cover is the pressure plate assembly of the clutch, 9 inch (229 mm) diameter, coil-spring type with three release fingers. It bolts to the ...

Low Range Gear

Inner Ring