Products

Viscous Fan Assembly for the engine cooling system, mounting to the viscous coupling unit on the front of the engine. This 16", 7-blade white fan ...

Transfer Box Output Shaft Felt Seal for the Series II and Series III LT15 transfer box. The waxed felt seal fits around the rear output shaft and ...

Gearbox Gasket for the LT67 manual gearbox. The gasket seals a mating joint on the gearbox casing, maintaining the oil seal between components and...

Gearbox-Transfer Box Gasket for the LT76 gearbox, sealing the mating joint between the gearbox and the transfer box. The gasket maintains the oil-...

Gasket

Gearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...

Gear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...

Fuel Level Sender for the petrol fuel tank, part of the fuel gauge system. The sender mounts in the top of the rear fuel tank, where a float arm f...

Fuel Level Sender for the petrol fuel tank, part of the fuel gauge system. The sender mounts in the top of the rear fuel tank, where a float arm f...

Fuel Tank Sender for the rear-mounted fuel tank on long-wheelbase diesel applications. The sender unit fits into the top of the fuel tank, where a...

Bottle Cap for the coolant expansion bottle. Seals the coolant expansion reservoir and maintains system pressure within the cooling circuit.

U-Bolt for clamping the front axle casing to the leaf spring, metric thread, round-bend profile. Three round-bend U-bolts are fitted per vehicle, ...

U-Bolt secures a leaf spring to its axle in the suspension. The U-shaped bolt passes around the axle tube and clamps down over the spring pack thr...

U-Bolt for the front axle leaf-spring mounting - the square-bend form. The U-bolt passes over the front axle and down through the spring plate, cl...

Coolant Pipe Adaptor for the engine cooling circuit. It threads into the thermostat housing / cylinder head coolant outlet to provide the connectio...

Exhaust Plate for the intermediate section of the exhaust system on 88" Short Wheelbase variants in left-hand drive (LHD) configuration. This plat...

Front Exhaust Pipe (downpipe) for the 2.25L diesel engine, forming the first section of the exhaust system. The front pipe bolts to the exhaust ma...

Exhaust Pipe Assembly Pipe section of the exhaust system, routing exhaust gas rearward from the manifold toward the silencer. Forms the left-hand ...

Accelerator Cable connecting the accelerator pedal to the throttle linkage on the 3.5L V8 petrol engine. The cable transfers pedal travel to the c...

Radiator Hose - the top hose of the engine cooling circuit, connecting the cylinder head outlet to the top of the radiator. It carries heated cool...

Past op 6-cylinder

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Mainshaft peg

Grommet

Gearbox Tie Rod Buffer for the gearbox steady (tie rod) mounting. The tie rod restrains the gearbox against fore-and-aft movement under load. This...

Cup Washer is a dished washer used at the gearbox tie-rod (stabiliser rod) to chassis mounting on Series models. The cupped profile seats against ...

Engine Oil - 15W40 Multigrade mineral engine lubricant for older petrol, diesel, and LPG engines. 15W40 multigrade viscosity provides reliable lub...

Drive Screw with a round head, a general body and chassis fixing. The steep-helix thread lets the screw be driven into a pre-drilled hole with a h...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Pan Head Screw - a 2BA x 1/2 inch slotted pan head fastener used across interior trim and body panel fixings. It retains interior trim panels and ...

Set Screw retaining the top cover plate of the Series gearbox. A 4BA round-head fastener, sherardised finish, used to secure the cover plate on to...

Fuel Filler Screw is a 2BA x 3/8" fastener used to secure the fuel filler fitting. It retains the fuel filler to the body panel; the companion nut...

Screw - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...

Windscreen Seal - 2.5m is the rubber glazing seal for the windscreen, supplied as a 2.5 m length. It seats the windscreen glass in its aperture an...

Bolt with a 1/4" UNF (Unified Fine) thread. A threaded steel fastener used to secure body panels and ancillary fittings.

Spire Nut is a spring-steel push-on fastener used to retain body panels and trim. The clip slides over a panel edge or hole and self-threads onto ...

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...

Screw for securing the window catch on Series hard top body variants. Used in the hard top glazing and catch assembly to retain the window catch m...

Screw securing the front catch of the rear side sliding window. Used to fix the sliding window catch on Station Wagon bodies of early Series models.

Speedometer Cable Plate Screw secures the speedometer cable retaining plate to the gearbox. It clamps the plate that holds the speedometer drive c...

Screw with a mushroom head and a 1/4" Acme thread, 1" long, with a sherardized zinc finish. Used as a floor fixing, securing the transfer lever ga...

Lokut Nut is a self-locking nut used to secure the headlamp to the body at the front wing. The self-locking design resists loosening under vibrati...

Screw for securing the chaffguard to the body structure on Series Land Rovers. The chaffguard protects adjacent components from abrasion and heat;...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Single Clip is a single-aperture retaining clip used to secure brake and fuel pipes, the accelerator cable and the hand throttle control. It holds...

Drive Screw retaining the direction-indicator switch clamp. A hammer-drive screw used to secure the indicator switch clamp, and the indicator cowl...