Products

Door Hinge Bolt for attaching door hinges to the body structure. This countersunk bolt secures the hinge plate to the hinge assembly, providing a ...

Nutsert - 1/4" UNF is a blind rivet nut (rivnut) with a 1/4" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal or...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Piston Ring Set for the 2.25L and 2.5L 4-cylinder petrol engine, supplying the ring pack for one piston. The rings seat in the piston ring grooves...

Piston for the 3.5L V8 petrol engine, standard (nominal) bore size. It reciprocates within the cylinder bore, transmitting combustion pressure thr...

Piston for the 3.5L Rover V8 petrol engine, supplied at +0.020" oversize with an 8.13:1 compression ratio. The +0.020" oversize suits a rebored bl...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Clutch Driven Plate (friction disc) for the clutch assembly, 9 1/2 inch diameter. The driven plate is clamped between the flywheel and the pressur...

Clutch Driven Plate (friction disc) for the clutch assembly, 9 1/2 inch diameter. The driven plate is clamped between the flywheel and the pressur...

Heater valve

Clutch slave cylinder overhaul kit

Inlet manifold stud

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

Oil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...

Halfshaft Collar is a locating collar fitted to the front axle halfshaft. It seats against the inner side of the halfshaft bearing (244150), setti...

Gearbox Thrust Washer

Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...

Output Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...

Bush

Stud used at the gearbox-to-chassis bracket mounting on Series models. A 7/16" BSF stud securing the gearbox mounting bracket to the chassis. Not ...

Spherical Bearing Bush - Clutch Cross Shaft for Series 1, Series 2, and Series 3 Land Rover vehicles. The clutch cross shaft is supported at its p...

Starter Motor for the 2.25L petrol engine, 24V system - part of the engine starting circuit. On cranking, the motor's pinion engages the flywheel ...

Fuel Tank Mount is a rubber mounting that supports the fuel tank on the chassis. It cushions the tank on its mounting bracket, isolating it from c...

Air Intake Hose for the 2.25 litre diesel engine, forming part of the air induction system between the air cleaner and the intake manifold. It car...

Air Intake Hose for the 2.25 litre diesel engine, forming part of the air induction system between the air cleaner and the intake manifold. It car...

Exhaust Valve Guide for the 2.6L six-cylinder petrol engine. The guide is pressed into the cylinder head and locates the exhaust valve stem, holdin...

Gasket thermostat by-pass Series 2.25 petrol and diesel.

Shakeproof Washer – a serrated, externally toothed lock washer used at the clutch hydraulic hose union. The teeth bite into both the mating surfac...

Input shaft oil seal

Cam Follower (tappet) in the valvetrain, riding on the camshaft lobe to transmit its motion to the pushrod and valve. It converts the rotating cam...

clamp exhaust

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Cylinder Head to Block Stud for the four-cylinder diesel engines - 2.25L and 2.5L naturally-aspirated. The stud threads into the cylinder block dec...

Camshaft Bearing, the front bearing in which the camshaft front journal runs within the cylinder block. It supports the forward end of the camshaf...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Camshaft Bearing for the 2nd, 3rd and 4th journal positions of the four-cylinder engine. The bearing shell is fitted into its housing in the cylind...

Stop bracket

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Oil Temperature Sender for the engine oil temperature gauge circuit. The sender threads into the oil gallery and carries a temperature-sensitive re...

Tank Sender Unit measures the fuel level in the under-seat fuel tank and signals it to the dashboard fuel gauge. A float-actuated variable-resista...