Products

Clevis Pin connecting the brake pedal push rod to the master cylinder actuation linkage. This pin forms the pivot joint between the brake pedal ar...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Brake Master Cylinder for the braking hydraulic system, converting brake pedal force into hydraulic pressure to actuate the brakes. Mounted to the...

Heater Hose – Inlet carries hot coolant from the engine cooling circuit to the heater matrix, forming part of the cabin heating system. The inlet ...

Tailpipe forming the rearmost section of the exhaust system on Series Land Rovers equipped with the 2.6L 6-cylinder engine. This pipe routes exhau...

Oil Pump Gasket for the LT95 four-speed gearbox. It seals the oil pump to the gearbox casing on the LT95 transmission, used behind the Rover V8 an...

Hazard Switch - the push-type dashboard switch that operates the hazard warning function. When pushed it flashes all four indicator lamps together ...

Exhaust Clamp for the V8 engine exhaust system, securing a front-pipe joint. The clamp draws two pipe sections together at their slip joint, holdin...

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...

Bolt – 3/8" BSF x 1-1/4" is a threaded fastener used in the front axle assembly, securing the swivel pin housing. The bolt has a 3/8 inch diameter...

Bolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...

Heater Control Valve regulates the flow of engine coolant into the heater matrix, forming part of the cabin HVAC heating circuit. The valve is cab...

Chassis Shackle Bush – Front is the compliant bush at the chassis end of the front spring shackle, part of the leaf spring suspension mounting. Th...

Chassis Shackle Bush – Front – Polyurethane is a set of four polyurethane bushes for the chassis end of the front spring shackles, part of the leaf...

Brake master cylinder LWB post-80

Spring Shackle connecting the end of a leaf spring to the chassis bracket, allowing the spring to lengthen and shorten as it deflects under load. ...

Shackle Plate, the side plate of the spring shackle assembly that forms the swinging link between the leaf spring eye and the chassis shackle brack...

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

Front Shackle Plate forms part of the front leaf-spring shackle assembly, connecting the road spring eye to the chassis mounting. The shackle allow...

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Gasket is a sealing gasket used in the V8 petrol engine assembly. It forms a seal between two mating components, preventing leakage of fluid or gas...

Folding side step Series

Brake Master Cylinder Repair Kit for overhauling the brake master cylinder on Series III models. The kit reconditions the internal sealing of the ...

Fuel Pump Gasket seals the external fuel pump to its mounting face in the fuel delivery system, preventing leakage at the joint. Used on petrol ap...

Windscreen Washer Non-Return Valve fits inline in the washer fluid delivery pipe, forming part of the windscreen washer system. It allows fluid to...

Pinion Lock Nut – Salisbury secures the drive pinion in the Salisbury rear differential, retaining the pinion flange and holding the pinion bearing...

Oil Seal – Rear Output Shaft seals the rear output shaft of the LT95 combined gearbox and transfer box, preventing oil leakage where the shaft exit...

Speedometer Drive Cable transmits rotational drive from the gearbox speedometer take-off to the speedometer head in the instrument panel. An inner...

Front Exhaust Pipe - downpipe section of the exhaust system. Connects the exhaust manifold to the intermediate pipe and silencer, carrying exhaust...

Steering Relay Gasket seals the steering relay assembly within the steering linkage. The steering relay transfers movement from the steering box d...

Gasket A large gasket for the 2.0L four-cylinder petrol engine. It forms a sealed joint between two mating engine components to prevent the leakag...

Camshaft Lock Washer retains the camshaft gear securing bolt at the front of the camshaft, part of the engine timing drive. After the bolt is tigh...

Circlip

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Brush set M418G

Accelerator Rod Ball Joint forms an articulated pivot in the accelerator (throttle) control linkage, joining adjacent sections of the accelerator r...

Carb overhaul kit 175CD V8 Zenith Stromberg

Pinion Oil Seal - seals the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Pinion Oil Seal - seals the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Starter Drive Kit is the pinion drive assembly for the Lucas inertia-type (Bendix) starter motor, operating within the engine starting circuit. Wh...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...