Products

Screw securing the brake pedal bracket mounting plate within the pedal box. It fixes the pedal bracket plate in position, retaining the brake peda...

Thermostat Housing Gasket seals the joint between the thermostat housing and the cylinder head water outlet in the engine cooling circuit. It main...

Differential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...

Outer Wing is the left-hand front wing outer skin panel, moulded in ABS plastic. It forms the visible outer surface of the front wing, covering th...

Front Wing Panel is the outer body panel covering the front wheel arch on the left-hand side, incorporating the headlamp aperture. Supplied as the...

Inner Pinion Bearing for the Salisbury rear axle. This taper-roller bearing supports the inner end of the differential pinion shaft, carrying the ...

Handbrake Tension Spring - the lower spring within the transmission (drum) handbrake assembly, fitted to vehicles with the LT95 four-speed gearbox....

Primary Pinion Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox (V8) casing. 2.10 mm thick, it controls p...

T-piece imperial

Seat Belt Buckle - Right-Hand - the latching receptacle of the seat belt restraint, into which the belt tongue (latch plate) engages and locks to h...

Seat Belt Buckle Catch - left-hand front seat belt stalk receiver forming the fixed lower end of the front LH seat belt assembly. The non-audible c...

Heater Distribution Control Cable - the Bowden cable that links the dashboard heater control to the air-distribution flap in the heater assembly. ...

Headlamp Bulb - a 24V dual-filament bulb for the main headlamp, rated 55/50W with a P45T base. The two filaments carry the main and dipped beam wi...

Water Pump Seal for the engine cooling circuit, sealing the water pump on four- and six-cylinder engines. The rubber seal seats the water pump aga...

Steering Relay Mounting Bolt - secures the steering relay to the chassis within the steering linkage. The steering relay transfers movement into t...

Bolt - threaded fastener with a 7/16" UNF (Unified National Fine) thread and a 2-1/4" length.

Timing Chain Tensioner maintains correct tension on the timing chain of the 2.6L 6-cylinder petrol engine. Acting against the chain run, it takes ...

Circlip for the handbrake (parking brake) linkage. This external retaining circlip secures the handbrake relay elbow onto its pivot post, holding t...

Circlip Retaining circlip for the gearbox rear output shaft. It seats in a machined groove on the output shaft, locating the adjacent component ax...

Glazing rubber

Strip - Glazing and Sealing

Glass seal EPDM

Jubilee Clip - 60-80mm is a worm-drive hose clip with a 60-80mm clamping range. The band is tightened by a captive worm screw to secure large-bore...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Hose Clip - Jubilee - 70-92mm is a worm-drive band clamp with a clamping range of 70-92 mm. It secures a hose over its spigot or connector, compre...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Front Door Glass Guide is a moulded plastic guide that locates the front door drop glass within its window channel. Fitted inside the door frame, ...

Front Door Glass Guide is a moulded plastic guide that locates the front door drop glass within its window channel. Fitted inside the door frame, ...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Body Panel Locknut for square-hole panel apertures, used in body, interior, and trim panel assemblies. This push-fit captive nut locates into a sq...

Glow Plug for the 2.25L diesel engine running a parallel (converted) glow plug system. Part of the cold-start pre-heating circuit. The glow plug h...

Bonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...

Rear Crossmember Bolt Kit - a set of stainless steel fixings for securing the rear crossmember to the chassis. The rear crossmember is the rearmos...

Castor Correction Wedges - a pair of tapered wedges fitted between the front axle and the leaf springs to restore the castor and differential pin a...

Capture the sleek design of the Range Rover Evoque with this premium 1:76 scale diecast model in elegant Baltic Blue. This detailed replica perfect...

Timing Chain Kit renews the timing drive of the 2.25L petrol engine, restoring accurate valve timing between the crankshaft and camshaft. The kit ...

C-Post Bottom Leg Repair Panel - Left Hand is a weld-in body repair section for the lower leg of the C-post, the rearmost body pillar of the Statio...

C-Post Bottom Leg Repair Panel - Right Hand is a weld-in body repair section for the lower leg of the C-post, the rearmost body pillar of the Stati...

Radiator panel Series 2/2A - suffix B to suffix F

HUB & BEARING KIT - S2A FROM SUFFIX H - S3 UP TO 1980

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Tailgate Seal Kit for the rear tailboard and tailgate. Reseals the rear tailboard and tailgate opening. The kit contains two tailboard seals, one ...

Seatbelt Mounting for the second-row seats, manufactured in stainless steel and supplied as a pair. Provides the anchorage point for the rear seat...