Products

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Fuel Tank Spill Return Pipe Gasket for the fuel tank assembly. This gasket seals the joint where the spill return pipe meets the fuel tank, preven...

Inline Fuel Filter for petrol fuel-injection (EFI) systems, fitted in the pressurised fuel supply line between the fuel pump and the injector rail....

Inlet Valve for the cylinder head valve train, with a 34.5 mm head diameter. The inlet valve opens on the induction stroke to admit the air/fuel c...

Valve Spring Cap for the cylinder head valve train. The spring cap seats on top of the valve spring and locates against the split collets on the v...

Valve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Oil Filter Adaptor for the engine lubrication circuit, mounting the oil filter to the cylinder block. The adaptor forms the interface between the ...

Banjo Bolt - M10 is the hollow fastener used to secure the oil feed pipe at the block-to-head junction in the lubrication circuit of the 2.25L and ...

Timing Chain for the 2.25L four-cylinder engine, part of the timing drive assembly. Drives the camshaft from the crankshaft sprocket, holding valv...

Exhaust Valve Stem Seal for the cylinder head valvetrain. Fits over the exhaust valve stem at the top of the valve guide, metering the oil that pa...

Exhaust Valve Stem Seal for the cylinder head valvetrain. Fits over the exhaust valve stem at the top of the valve guide, metering the oil that pa...

Thermostat 74C

Thermostat

Thermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...

Connecting Rod Nut - the big-end nut that secures the connecting rod cap to the rod bolts. The nut clamps the connecting rod bearing cap onto the ...

Conrod

Timing Chain for the 2.25L and 2.5L four-cylinder petrol engines with the five-bearing crankshaft, running inside the front timing cover. It drive...

Camshaft Sprocket for the engine timing drive assembly. Mounted on the nose of the camshaft and driven by the timing chain from the crankshaft spr...

Inlet Valve for the 2.25L and 2.5L four-cylinder diesel engines, including the 2.5L Turbo Diesel, operating in the cylinder head valve train. It o...

Flywheel - 5-Bearing is the rotating mass mounted to the rear flange of the crankshaft in the 5-main-bearing variant of the 2.25L and 2.5L 4-cylind...

Distributor - contact-breaker (points) ignition distributor for the 4-cylinder petrol engine. Distributes the high-tension spark to the cylinders ...

Electronic Distributor - complete distributor assembly for the 4-cylinder petrol engine, supplied with the electronic ignition conversion already f...

Electronic Distributor for the ignition system of the 4-cylinder petrol engine. It distributes high-tension voltage from the ignition coil to each...

Electronic Conversion Kit - electronic ignition conversion for the 4-cylinder petrol points distributor. Replaces the contact breaker points and c...

Exhaust Valve for the 2.25L 4-Cylinder Petrol engine, fitted in the cylinder head valvetrain assembly. This valve operates in the cylinder head to...

Rocker Cover Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. This gasket seals the joint between the rocker cover and the cylinde...

Rubber-Lined Sealing Washer - a metal sealing washer with a bonded rubber lining, fitted under a bolt or union to seal the joint. As the fitting i...

Fuel Pipe is a fuel line for the 2.25 litre diesel engine, forming part of the fuel delivery system. It carries fuel between components of the fue...

Rocker Cover encloses the top of the cylinder head, covering the rocker gear and valve train and containing the oil within the head. Designed for ...

Camshaft for the five-bearing four-cylinder engine, running in the cylinder block as the core of the overhead-valve valvetrain. Driven from the cr...

Inlet Manifold Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. Fitted between the inlet manifold and the cylinder head, this gask...

Inlet Manifold Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. Fitted between the inlet manifold and the cylinder head, this gask...

Oil Dipstick - engine oil level gauge for the 4-cylinder engine. Inserts into the dipstick tube to read the oil level in the sump, marked with min...

Oil pump relief valve washer V8

3 man seat Techno Exmoor trim EX4188 EXT006-TC

Rubber Mat - a heavy-duty 6mm rubber floor mat for the rear load area of hardtop models. Laid over the load-area floor, the 6mm rubber protects th...

Door Drain for the left-hand door, fitted to the lower edge of the door to channel water away. Water that runs down inside the door skin past the ...

Screen to Drain Bracket for the right-hand side, securing the windscreen frame to the drain channel at the base of the screen. The bracket ties th...