Products

Sill Protector in aluminium, fitted over the outer sill panel below the door apertures to shield the original sill from stone chips, mud abrasion a...

Differential Cover is the pressed plate that closes the differential aperture in the axle casing, retaining the axle oil and giving access to the c...

Rear Door Protection Plate mounts on the exterior of the rear door to shield the panel from stone chips, scuffs and impact damage during loading an...

Rear Sill Panel - Left-Hand is a lower-body repair panel for the rear sill section on the nearside (left-hand) of the body. It forms the outer clos...

Rear Sill Panel - Right-Hand is a lower-body repair panel for the rear sill section on the offside (right-hand) of the body. It forms the outer clo...

Wiring Harness Set is the main electrical loom that carries power and signal connections through the vehicle's electrical system, tying the chargin...

Quarterback chassis for Serie 2/3 88" military, including Lightweight. The rear spring leaf supports are included, as well as the support of the fi...

Battery Carrier is the mounting tray that holds and locates the battery, supporting it and retaining it against movement and vibration. It forms t...

Trailer Plug - a 7-pin towing connector that links the towing vehicle's electrical circuit to a trailer or caravan. It carries the supply for the t...

Fuel Tank Outrigger is a lateral chassis support bracket within the main frame structure. Welded to the chassis side rail, it carries the front mo...

Wheel Arch Kit is a four-piece set of moulded ABS plastic wheel arches. The kit comprises four wheel arch sections covering the front and rear arc...

Front door pillar repair section for the left-hand side — the A-post that forms the rear edge of the bulkhead and carries the front door hinges. T...

Bulkhead Door Pillar for the right-hand (offside) front door aperture, in the basic configuration. The door pillar forms part of the bulkhead asse...

Door Pillar Bracket for the right-hand (offside) bulkhead door pillar, supplied as the bottom bracket only (less the pillar). The bracket forms th...

Rear Crossmember with 325mm Extensions for the military Lightweight (Air Portable) 88" chassis. The rear crossmember closes and braces the rear of...

Chassis front crossmember Series LHD & RHD (WITHOUT the front chassis legs)

T-Piece Hose Connector is a three-way junction fitting used in a flexible hose run. It joins three hose ends at a single point, allowing a hose li...

Lamp Boot - Military is a rubber protective boot for military-specification lamp assemblies. The boot fits over the lamp body to provide a weather...

Rear Main Bearing Cap Seal for the Rover V8 petrol engine, sealing the joint between the rear main bearing cap and the cylinder block. This crucif...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Manifold Absolute Pressure (MAP) Sensor, part of the engine management system. The MAP sensor measures the absolute pressure inside the intake man...

Fuel filler breather hose

Washer is a nylon door hinge washer used on the hinge fixing bolts. It fits over the hinge bolt as a low-friction spacer between the moving hinge ...

Captive Nut with a UNF thread, providing a fixed threaded anchor point for a bolted fixing. The nut is retained in its bracket or panel so it cann...

Door Hinge Bolt - countersunk UNF type - within the door assembly. This countersunk fixing bolt secures the door hinge plate to the door face, com...

Lightweight Vent Seal

Rear Light Guard - Single - Natural is a steel mesh protective guard for a single rear lamp. It bolts over the rear lamp lens to shield it from im...

Rear Light Guard - Single - Black is a steel mesh protective guard for a single rear lamp. It bolts over the rear lamp lens to shield it from impa...

Fume Curtain – Khaki Canvas is a canvas curtain that hangs across the rear of a soft-top vehicle to reduce the volume of exhaust fumes drawn into t...

Mirror Arm within the external rear-view mirror assembly. This arm mounts at the door hinge position and extends outward to position the mirror he...

Spare Wheel Bonnet Buffer is a rubber buffer for the bonnet-mounted spare wheel carrier. It sits between the spare wheel and the bonnet, cushionin...

Door Check Strap Bracket – Rear – RH mounts the door check strap on the right-hand rear side door. The check strap limits how far the door swings ...

Door Checker Bracket Assembly - Rear - LH is the door check mechanism for the left-hand rear door. It links the door to the body pillar and limits...