Products

Accelerator Cable for the throttle control linkage, transmitting accelerator pedal movement to the carburettor throttle on the 2.25 litre petrol en...

Brake hose metric

Brake Hose is a flexible hydraulic line in the braking circuit, carrying fluid from the rigid chassis-mounted brake pipe to the caliper or wheel cy...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Thin Nut - a reduced-height hex nut with a 5/16" UNF (Unified Fine) thread. The shallow profile suits fastening points with limited clearance and ...

Hex Nut, 3/8" UNF. A general-purpose threaded fastener used at fixing points across the braking, chassis and body assemblies. The 3/8" Unified Nat...

Air cleaner to carburettor hose

Left-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the left cylinder bank exhaust manifold outlet ...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Exhaust pipe clamp 2.6 Stage 1 V8

Brake Hose - flexible hydraulic line in the rear braking circuit, connecting the chassis-mounted rigid brake pipe to the rear axle brake assembly. ...

Grab Handle chassis-mounted exterior fitting, bolted to the vehicle chassis. It provides a fixed hand-hold at the chassis, giving a secure grab po...

Radiator for the engine cooling system, mounted at the front of the vehicle to dissipate heat from the coolant circulated by the water pump. Air dr...

Brake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...

Hex nut

Nyloc Nut M5 - M5 hex nyloc (nylon insert) locknut. The nylon insert creates friction against the thread to resist loosening under vibration. Stan...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Nyloc Nut - 1/4" UNF - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under ...

Self-Locking Nut with a 5/16" UNF thread and a 1/2" across-flats hexagon. The self-locking action resists loosening under vibration, retaining cla...

Nyloc Nut with a 3/8" UNF thread and a 12 mm across-flats hex, in the full-height (thick) form. A nylon insert set into the crown of the nut defor...

Lock Nut - 7/16" UNF - self-locking nut providing a prevailing-torque fastening. The nut resists loosening under vibration and dynamic load, secur...

Nyloc Nut with a 1/2" UNF thread, used to retain suspension and steering ball-joint fixings. A nylon insert set into the crown of the nut deforms ...

Nyloc Nut with a 3/8" UNF thread, used to secure propshaft flange bolts. A nylon insert set into the crown of the nut deforms over the bolt thread...

Clevis Pin for the handbrake (transmission parking brake) linkage. This 22mm clevis pin connects the handbrake operating rod to the relay lever, t...

Battery - Wet Non-Spillable - sealed lead-acid starting and deep-cycle battery with dual terminals. Rated at 68 Ah with 1500 cranking amps. The pl...

Coolant Expansion Tank Cap – the pressure-relief cap that seals the cooling system's expansion (header) tank. Rated to 15 psi, it holds the system...

Low Fuel Monitor Unit for 24V electrical systems, operating in the fuel level indication circuit. The unit processes the signal from the fuel tank...

Worklamp Autolite square 1x 55W

Pop Rivet (blind rivet) used to secure the flexible door rubber, a body and door-trim fixing. The rivet fastens the flexible rubber seal to the do...

Wiper Blade for the front windscreen, with a stainless steel frame. The blade clears the driver's field of view across the front windscreen. It at...

Main Wiring Loom for right-hand drive vehicles, forming the primary electrical harness that distributes power and signal throughout the vehicle. I...

Heater (Glow) Plug Ballast Resistor for the diesel pre-heat circuit. Wired in series with the heater plugs, the resistor drops the battery supply t...

Engine Wiring Harness for the Series III 109" Stage 1 fitted with the Rover V8 petrol engine. This harness forms the main electrical distribution ...

Speedo cable S3

Oil Temperature Transmitter for the engine instrumentation circuit. The transmitter threads into the oil gallery and varies its electrical resistan...

Windscreen Washer Jet directs washer fluid onto the windscreen as part of the front wash/wipe system. This single jet is bulkhead-mounted and fed ...

Temperature transmitter

Speedometer instrument head for the dashboard instrument panel, incorporating a resettable trip odometer alongside the main total odometer. The sp...

Wiper Arm - front windscreen wiper arm, left-hand. The 5mm is the narrow width of the arm, which sets the wiper-blade fitting - it is not a spindl...

Wiper Arm - front windscreen wiper arm, right-hand. The 5mm is the narrow width of the arm, which sets the wiper-blade fitting - it is not a spind...

Main Wiring Harness for the Series III Stage 1 V8 Petrol, left-hand drive, 109-inch long-wheelbase configuration. This is the primary electrical w...