Products

Stekker 7-polig Pvc

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Bonnet Canvas Rest Strip for the front body assembly. This canvas strip mounts across the top of the radiator/front panel, forming the surface the ...

Cleat Rope Hook Body Side All and Classic (Softtop) - Series Defender

Gear Lever Gaiter for the transmission tunnel. This flexible boot fits around the base of the gear lever where it passes through the tunnel, sealin...

Hinge Pin - the pivot pin for the top hatch (windscreen) hinge. It passes through the hinge knuckles to retain the two halves of the hinge while a...

Weatherstrip for the alpine light (side roof window) glass. This rubber sealing strip retains and seals the 5mm glass panels of the alpine lights ...

Panel Rivet - a round-head solid rivet for body panel fixing. Used to join body panels and brackets, it has a domed (round) head, a 3/16 in shank ...

Washer

Spiralok Nut for body panel and interior trim fixings. This spring-steel speed nut (clip nut) clips to a panel flange or through a mounting hole a...

Rivet, semi-tubular with a semi-round (truss) head, 3/16 in diameter and 3/8 in long. It secures door weatherstrip and seals to the body aperture....

Chain Bracket Series/Lw

Clevis Pin for the tailboard assembly at the rear of the body. It secures the drop-down tailboard's support cable or chain to its anchor bracket, ...

Special Bolt with a coarse ACME-form thread, 1/4 in diameter and 5/8 in long. It is a body fixing used to secure inner-wing mudshields, floor plat...

Gaiter Retainer - secures the rubber gaiter around the high-low (transfer) lever on the LT76 gearbox, which carries an integral transfer box. The ...

Tailgate Seal for the lower edge of the rear tailboard. It seats along the bottom of the drop-down tailgate and seals against the body, keeping wa...

Centre Squab Buffer - a rubber buffer that cushions the centre seat squab (backrest) against the surrounding bodywork. It prevents metal-to-metal ...

Hoodstick Bracket Clamp - secures a hoodstick to its mounting bracket within the soft-top frame. The clamp holds the hoodstick (the soft-top frame...

Rope Hook - a securing hook for the canvas hood (soft top). It provides an anchor point around which the hood tie-down rope is passed, holding the...

Body Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...

Rear Quarter Seal - the rubber glazing seal that secures the fixed rear quarter window into the hard-top body aperture. Sized for 5mm glass, it be...

Interior Grab Handle - interior pull handle for the rear side door, used to draw the door closed from inside the cab. It fixes to the inner face o...

Rear End Door T-Handle and Lock Assembly for the upper tailgate on hard top body configurations. The handle operates the latch mechanism to release...

Door Clevis Pin for the door check strap mechanism. The pin locates the check strap to its mounting bracket, forming the pivot the strap works aga...

Spring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...

Washer

Ignition Switch Knob - the rotary knob for the PRS-type combined ignition and lighting selection switch. It fits onto the switch spindle to provid...

Floor Panel Screw with a mushroom head profile, used to secure floor plates and lower rear body panel assemblies on the Defender. The low-profile ...

Floor Panel Screw x 100

Upper Tailgate Lock Cap for the rear end door handle assembly. This small plastic cap fits over the end of the upper tailgate handle, covering and...

Rear Mudflaps - a pair of rear mudflaps for the 88in short-wheelbase, fitted behind the rear wheels to deflect road spray and debris thrown up by t...

Rear Mudflaps - a pair of rear mudflaps for the 88in short-wheelbase, fitted behind the rear wheels to deflect road spray and debris thrown up by t...

Front Mudflaps, supplied as a pair. The mudflaps mount behind the front wheels to deflect road spray, mud and stones thrown up by the tyres, prote...

Lower Tailgate for the rear of the body - the drop-down tailboard panel that closes off the rear of the load area. Hinged along its lower edge, it...

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Barrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Bench Seat Backrest in black vinyl, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts to ...

Bench Seat Backrest in techno fabric, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts t...

Front Outer Seat Cushion Base for the adjustable seat frame in Series II, IIA, and III 109" long-wheelbase vehicles. This is the outer seat base c...

Inner Seat Base is the centre front seat base cushion, forming the lower seating platform of the basic vinyl front seat. Finished in black vinyl f...

Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...

Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...