Products

Road Spring SWB Rear 11L

Rear left-hand leaf spring designed for short wheelbase Land Rover Series vehicles. This road spring is configured with 11 leaves and is intended ...

Front Exhaust Pipe for petrol applications. This is the front section of the exhaust system, carrying gases from the exhaust manifold rearward to t...

Wiper Gear Linkage for the windscreen wiper system, transmitting drive from the wiper motor to the wheelbox and wiper spindle. It converts the rot...

Wiper Gear Linkage for the windscreen wiper system, transmitting drive from the wiper motor to the wheelbox and wiper spindle. It converts the rot...

Union Nut for the diesel fuel filter housing, part of the fuel supply circuit. The union nut secures a fuel feed pipe union to the filter housing,...

Washer - Diesel Sedimentor is a sealing washer used in the diesel fuel sedimentor (fuel filter/water separator) assembly on diesel-engined Land Rov...

Air Intake Hose for the 2.25L and 2.6L petrol induction system. This flexible rubber hose connects the air filter housing to the carburettor intak...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

Rubber Mat

Side Step Tread Rubber

Slip Ring for the horn contact in the steering column. This contact ring maintains the electrical connection to the horn as the steering wheel tur...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Brake master cyl SII SWB

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Circlip for the throttle linkage on the carburettor V8 engine. It retains a pin or clevis within the throttle linkage, holding the linkage componen...

Mainshaft Nut - castellated nut that retains the assembled components on the rear of the gearbox mainshaft. The castellations accept a split pin to...

Gearbox Mainshaft Washer - the washer that sits in the retaining-nut stack at the rear of the gearbox mainshaft, seating beneath the mainshaft lock...

Bush - Low Gear Wheel is a gearbox internal bush fitted to the low gear wheel in the Series 2 and Series 3 manual gearbox on 109-inch 1-ton Land Ro...

Screw - a set screw for the gearbox top cover plate. It secures the cover plate to the top of the main gearbox casing. Not used on the Stage 1 V8 ...

Washer used within the ignition system of four-cylinder petrol engines, associated with the distributor, ignition coil, HT leads and spark plug ins...

Crankshaft Oil Seal is the outer (rear) crankshaft seal in the engine sealing arrangement, fitted where the crankshaft exits the cylinder block. S...

Grab Handle for the rear end door, mounted externally on the rear door casing. It provides a fixed handhold at the rear of the vehicle, giving a s...

Cylinder Head Shroud - the injector shroud fitted into the cylinder head of the 2.25L diesel engine. It seats in the head around the injector, shi...

Cup Plug - a cup-type core plug (also known as an expansion or welch plug) that seals a casting core hole in the cylinder block or cylinder head. ...

Locating Screw for the engine. A locating screw sets and holds the position of a component against its mounting during assembly. Applies to the 2....

Core Plug, 1 7/8" diameter, sealing a casting core hole such as those in the inlet manifold and engine castings. Core plugs close the openings lef...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Bolt with a 5/16" UNF thread and a shank length of 2-3/4 inches. A standard-thread fastener used in assembly of the four-cylinder engine. Applies ...

Bottom End Gasket Set for the overhaul of the 2.25L diesel engine (3- and 5-main-bearing), covering the gasket and joint requirements of the lower ...

Track Rod Tube - 109.5cm - Part-Threaded Ends

Thermostat Gasket for the thermostat housing on the 2.25L petrol engine. This paper gasket seals the thermostat housing to the cylinder head, prev...

Crankshaft - 3-Bearing

Thermostat O-Ring for the 2.25L petrol engine cooling system. This O-ring provides a coolant-tight seal within the thermostat housing assembly. It...

Gudgeon Pin Bush - the small-end bush pressed into the connecting rod for the gudgeon pin. It forms the bearing surface between the gudgeon (pisto...

lock washer. sold EACH.

Clutch Withdrawal Unit Gasket - seals the mounting joint where the clutch withdrawal (release) housing bolts to the gearbox bellhousing. Part of t...

Gearbox Front Layshaft Bearing for the LT76 main gearbox, supporting the front end of the layshaft (cluster gear) within the gearbox casing. It ca...

Thrust Washer for the upper swivel pin Railko bush, part of the front axle steering swivel assembly. The Railko bush forms the upper pivot bearing...

Layshaft (countershaft) for the manual gearbox, specific to the Suffix B and C gearbox builds. The layshaft carries the constant-mesh cluster gear...