for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Radius Arm - front axle locating link in the coil-sprung front suspension, tying the front axle to the chassis and controlling fore-and-aft axle lo...
View full detailsLong-Travel Spring Relocation Cone - replaces the standard coil spring seat so the spring can dislocate (drop out of its seat) at full axle droop a...
View full detailsTop Shock Mount - upper shock absorber mounting for extreme long-travel suspension. This mount repositions the upper shock pickup point to accept ...
View full detailsCranked Rear Radius Arm - links the rear axle to the chassis, controlling fore-and-aft axle location and reacting drive and braking torque. The cr...
View full detailsRadius Arm - front axle locating link in the coil-sprung front suspension. The radius arm ties the front axle to the chassis, controlling fore-and-...
View full detailsShock Turret forms the upper mounting point for the front shock absorber on the chassis, within the front suspension assembly. Tubular fabricated ...
View full detailsSpring Dislocation Cones - Front are fitted inside the front coil springs to prevent spring dislocation under maximum suspension droop. During extr...
View full detailsTerrafirma mega sport competition 11"" travel kit for 90/D1/RRC
Mega Sport Shock & Mount Kit is a complete 11-inch travel suspension damping package, pairing four Mega Sport shock absorbers with their dedica...
View full detailsMega Sport Shock & Mount Kit providing 9 inch of shock travel across the front and rear suspension. The kit comprises front and rear Mega Spor...
View full detailsTerrafirma 5"" extreme LT dislocation kit for 90/D1/RRC
Terrafirma 2"" pro sport maxi dislocation kit for 90/D1/RRC
Extreme Long Travel Shock Absorber damps the suspension on vehicles set up for extended axle articulation, controlling spring and wheel movement to...
View full detailsTrack Rod Clamp secures the adjustable joint of the steering track rod. Fitted around the split end of the rod, it pinches the threaded sleeve clos...
View full detailsSeat Belt Anchor Plate twin anchor plate for the rear seat belt assembly, of the forward-facing outer static type. The plate forms the male anchor...
View full detailsDifferential Cover is the pressed plate that closes the differential aperture in the axle casing, retaining the axle oil and giving access to the c...
View full detailsRear Brake Disc, cross-drilled and grooved. Fitted to the rear axle. The cross-drilling and grooving help clear gas, dust and water from the pad c...
View full detailsConstant-Velocity (CV) Joint for the front axle drive, non-ABS applications. Heavy-duty specification. The CV joint sits at the outer end of the f...
View full detailsCV & Stub Shaft Assembly for the front axle drive, combining the constant-velocity joint with its stub shaft. It transmits drive from the halfs...
View full detailsGearbox Bearing Kit - LT77 - Suffix A-E for overhaul of the LT77 gearbox. This kit supplies the bearings required to rebuild the LT77 five-speed m...
View full detailsGearbox bearing kit Defender LT77 ( suffix H )
Gearbox bearing kit Defender LT77 ( suffix F-G )
Raised Air Intake Mantec - 90/110 200TDi
Rear Coil Spring for the rear suspension, raising ride height by approximately 40mm over standard. Wound from 18mm wire with a free height of 445m...
View full detailsDifferential Guard - a wrap-around steel guard that shields the front or rear differential housing from impact and debris during off-road use. Des...
View full detailsSpecial Bolt
Stop Lamp Cover for the high-level (high-mounted) centre stop lamp. This cover forms the outer lens of the high-mounted stop lamp assembly at the ...
View full detailsGearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...
View full detailsReceiver Hitch Recovery Point - a machined steel recovery point that inserts into a 2-inch square receiver hitch and is machined to accept a standa...
View full detailsFitment: Defender van 1994 tot 2007 Discovery 1 van 1989 tot 1994 Range rover Classic
Hydraulic Bump Stop Mounting Kit - Front is the front-axle mounting hardware for a hydraulic bump stop installation, sitting within the suspension ...
View full detailsRear Top Shock Mount Relocator - repositions the upper rear shock absorber mounting 50 mm (2 in) lower on the chassis. Dropping the top mount incr...
View full detailsTerrafirma rear spring retaining plates 90/D1/RRC
Rear Shock Absorber damps the rear suspension within the suspension assembly, valved for a +2" (50mm) raised ride height. Offers 8-stage adjustabl...
View full detailsFront Shock Absorber damps the front suspension within the suspension assembly, valved for a +2" (50mm) raised ride height. Fitted with a remote r...
View full detailsAdjustable Panhard Rod - lateral axle locating link within the suspension assembly. The Panhard rod ties the axle to the chassis and controls side...
View full detailsHydraulic Bump Stop & Mounting Kit is a complete progressive end-of-travel control package for the suspension, combining four hydraulic bump st...
View full detailsTerrafirma 2"" pro sport mini dislocation kit for 90/D1/RRC
Shock Absorber - front suspension damper with four-stage adjustable damping, sized for +2 inch raised ride height. Fitted between the chassis and ...
View full detailsRear Shock Absorber for the rear axle suspension, damping spring oscillation and controlling vertical wheel movement between the rear axle housing ...
View full detailsFront Shock Absorber for the front axle suspension, damping spring oscillation and controlling vertical wheel movement between the front axle housi...
View full detailsHex Bolt, grade 8.8, M8 x 20mm. A standard metric hexagon head bolt. Grade 8.8 indicates a tensile strength of 800 MPa and a yield strength of 640...
View full detailsFront Radius Arm Mount is the chassis bracket that anchors the front radius arm to the chassis on the left-hand side. The radius arm controls fore...
View full detailsSynchro Unit - the 1st/2nd gear synchromesh assembly carried on the mainshaft of the LT77 five-speed manual gearbox. The synchro hub is splined to...
View full detailsDifferential Gear Kit is a set of differential gears for the Rover-type axle differential, in the 10-spline configuration. The differential gears ...
View full detailsStripped Engine Unit for the 2.5L 300 TDi four-cylinder turbo diesel – the reconditioned core mechanical assembly of the engine. Supplied in strip...
View full detailsHandbrake Return Spring for the rod-operated transmission parking brake on the LT230 transfer box, in the horizontally mounted shoe arrangement. T...
View full detailsExhaust Valve for the cylinder head valvetrain of the 3.5 V8 petrol engine. The exhaust valve opens to release burnt gases into the exhaust port a...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →