Land Rover Old Defender 90, 110 & 130 Parts

LT230 Intermediate Shaft O-Ring, sealing the intermediate shaft within the LT230 two-speed transfer box main casing. The intermediate shaft transm...

Gear Knob - gear lever knob for the R380 5-speed manual gearbox. Threads onto the gearchange lever, forming the driver's hand grip and gear-select...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Water Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...

Fuel Connector Assembly - Pressure Regulator forms part of the fuel pressure-regulation circuit, providing the mounting and connection interface fo...

Slipper pad

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Crankshaft Position Sensor for the Td5 2.5L 5-cylinder turbo diesel engine management system. The sensor reads the toothed reluctor on the flywheel...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Oil Pressure Switch for the V8 petrol engine, forming part of the engine oil pressure warning circuit within the lubrication system. The switch th...

Air flow meter TD5 OEM VDO /Delphi

Voor LT77 versnellingsbak

Oil cooler adapter gasket

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Gearbox Oil 75W80 is a 75W80-grade manual transmission fluid (MTF) formulated for the R380 5-speed manual gearbox. It lubricates the gears, synchr...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Rubber Mounting A flexible rubber isolation mount used in the exhaust gas recirculation (EGR) system and air-cleaner assembly. It locates and supp...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Flange Screw, M6 x 16mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washer...

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Fuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Head Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the joint between the cylinder head and the cylinder block. It seals the comb...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

ATF - Dexron III is an automatic transmission fluid meeting the Dexron III specification, supplied in a 5 litre container. It is a hydraulic fluid...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Polyvee Auxiliary Drive Belt running in the engine front-end auxiliary drive, transmitting rotational drive from the crankshaft pulley to the alter...

Speedo cable oil seal retainer plate

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

CuNiFer Clutch Pipe, 1/4" outer diameter, supplied for the clutch hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough t...

Oil Seal for the input shaft of the ZF automatic gearbox. The seal fits at the front of the gearbox, where the torque converter drives the input s...

Oil Pump Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the oil pump to its mounting on the engine. It clamps the pump body agains...

Head Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the joint between the cylinder head and the cylinder block. It seals the comb...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Water Pump for the 200TDi 2.5L turbo diesel engine, operating in the engine cooling circuit. Belt-driven from the crankshaft, the pump circulates ...

Oil seal

Oil Pressure Switch monitors pressure in the engine lubrication circuit and signals the instrument gauge and low-pressure warning lamp. Mounts to ...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Flange Bolt - M8 x 85mm hex bolt with an integrated flange beneath the head. The flange spreads the clamping load across a wider bearing surface a...

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...