for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Selector Fork for the 5-speed manual gearbox internal gear-change mechanism. The selector fork engages with the synchromesh hub sleeve to move the...
View full detailsOil Filter Adaptor for the Td5 2.5L five-cylinder turbodiesel engine. Mounts to the engine block and provides the threaded interface for the oil f...
View full detailsTD5 Engine Designation Decal - silver, approximately 13 cm - for Td5-engined Land Rover models. This is the silver adhesive "TD5" lettering decal ...
View full detailsSynchro Ring - 5th Gear - R380 is the baulk ring for the 5th gear synchromesh assembly in the R380 5-speed manual gearbox. The ring equalises the ...
View full detailsCylinder Head Gasket Set for the Td5 2.5L 5-cylinder turbo diesel, supplying the ancillary seals and gaskets used around the cylinder head when it ...
View full detailsTurbocharger Hose
Sump Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. It seals the joint between the oil sump and the cylinder block within the engine lubri...
View full detailsO-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...
View full detailsCrankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...
View full detailsTemp Sensor
Screw: pan head self-tapping screw.
Locking Wheel Nut Key - Code F for removing locking wheel nuts with the Code F drive profile, fitted to alloy wheels across the Defender, Discovery...
View full detailsRelease Bearing Guide for the clutch assembly on TD5 engine applications with the R380 5-speed manual gearbox. The release bearing guide (also kno...
View full detailsHook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...
View full detailsEngine Dowel, a precision locating dowel that sets the relative position of mating engine components during assembly. The dowel fixes the exact al...
View full detailsHex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...
View full detailsProtective Coating Kit - Tintable (4 L) for applying a durable, textured surface coating to body panels, underbody areas, wheel arches, load beds, ...
View full detailsScrew for securing the engine wiring harness in Rover V8 petrol engine installations. Fastens harness clips and mounting brackets to the engine bl...
View full detailsRivet used within the main wiring harness assembly to secure harness routing and retain protective coverings to body mounting points. Maintains st...
View full detailsNeedle Roller Bearing for the R380 manual gearbox. It carries the reverse idler on the layshaft, allowing the gear to rotate with minimal friction ...
View full detailsNeedle Roller Bearing for the manual gearbox mainshaft. The bearing carries a constant-mesh mainshaft gear, letting it spin freely on the mainshaf...
View full detailsLock Nut for the front output shaft, used in the transfer box assembly. This nut secures the front output shaft drive flange within the transfer b...
View full detailsSnorkel Head is the 3" ram-air intake head that fits to the top of a raised air intake tube, forming the forward-facing scoop that feeds cool, clea...
View full detailsConrod
Brake Union - Blanking Plug, male thread, M10 x 1mm, short body. Used in the metric hydraulic brake circuit to blank off an unused or redundant po...
View full detailsSetscrew used as a general-purpose fastener in engine bay ancillary and drivetrain assemblies. Applied at engine harness mounting points, bell hou...
View full detailsSelector Roll Pin for the LT77 and R380 5-speed manual gearboxes. The roll pin secures a selector fork to its selector shaft, locking the two toge...
View full detailsBanjo Bolt for the turbocharger oil feed pipe on the Td5 engine. This M12 x 1.0mm thread banjo bolt clamps the hollow banjo fitting of the oil sup...
View full detailsBreather Tube for the LT230 transfer box. This tube forms part of the breather system on the LT230 transfer gearbox, routing pressure venting away...
View full detailsSelector Fork for the 3rd and 4th gear positions in the five-speed manual gearbox (LT77 and R380). The fork engages the 3rd/4th synchro hub sleeve...
View full detailsKey Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...
View full detailsPanhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...
View full detailsWastegate Modulator for the turbocharger boost control system. This electro-pneumatic solenoid valve is controlled by the engine ECU and regulates...
View full detailsGearbox Reconditioned Exchange - R380 68a-l
Automatic Transmission Oil Pump for the 4-speed automatic gearbox, part of the transmission's internal hydraulic system. The pump sits at the fron...
View full detailsScrew - M8 x 25mm is a fastener used in the assembly of the LT230 transfer gearbox. The LT230 is a two-speed transfer box fitted to Defender, Disc...
View full detailsExhaust Pipe - Front with Catalytic Converter for the Td5 2.5L five-cylinder turbo diesel. This front section runs from the turbocharger outlet fla...
View full detailsO-Ring for the oil strainer in the ZF 4-speed automatic transmission. This seal fits the oil strainer (the automatic transmission fluid pickup fil...
View full detailsPan Head Screw, M6 x 12mm. Metric pan head screw for use across a range of Land Rover body, chassis, and electrical assemblies.
Locking Wheel Nut Key - Code C for removing locking wheel nuts with the Code C drive profile. The key engages the unique recessed socket of the Co...
View full detailsOil Pump for the R380 manual gearbox. Mounted at the rear of the gearbox and driven from the output shaft, the pump circulates gearbox oil to lubr...
View full detailsStud - Turbo Outlet to Downpipe Flange in the exhaust system of the Td5 2.5L 5-cylinder turbo diesel engine. This stud secures the turbocharger ou...
View full detailsThrust Washer is a 1.15mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...
View full detailsDowel is a precision locating pin that aligns mating components during assembly, setting their position accurately and relieving the securing bolts...
View full detailsSynchromesh Ring for the R380 5-speed manual gearbox, the intermediate ring for 1st to 4th gears. The synchroniser ring matches the speed of the s...
View full detailsInlet Valve for the cylinder head valvetrain of the Rover V8 petrol engine (3.5L, 3.9L, 4.0L and 4.6L variants). It seats in the cylinder head inl...
View full detailsFlanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...
View full detailsAutomatic Transmission Shaft is a coupling shaft within the ZF 4-speed automatic gearbox assembly. This shaft transmits drive between internal gea...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →