for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Front Brake Disc - Solid. Solid (non-ventilated) front brake disc for the front axle brake assembly. It mounts to the front hub and provides the f...
View full detailsDoor Lock Escutcheon in black, part of the door casing and lock trim. The escutcheon is the moulded finisher that fits over the aperture in the do...
View full detailsWindow Seal - glazing seal for the cab body rear panel window, part of the cab rear panel glazing assembly. The seal locates in the rear panel ape...
View full detailsRubbing Strip - protective strip fitted to the front seat back, part of the front seat frame and trim assembly. It runs along the seat back where ...
View full detailsNut for the diesel fuel injection pump and timing gear. Secures the drive gear to the high-pressure fuel injection pump on the 2.7L Lion V6 diesel...
View full detailsInjector Seal Kit for the Td5 2.5-litre five-cylinder turbo diesel, renewing the sealing components at all five injectors. The kit contains five c...
View full detailsExterior mirror head for the left-hand side, with flat glass. The complete head assembly - housing, backing plate and glass - that mounts to the ar...
View full detailsExterior mirror head for the right-hand side, with flat glass. The complete head assembly - housing, backing plate and glass - that mounts to the a...
View full detailsScrew - threaded fastener used in vehicle assembly.
Clutch Release Lever Pivot provides the fulcrum for the clutch release lever. The release lever pivots on this point to transfer slave-cylinder mo...
View full detailsRadiator Hose for the engine cooling system - the top coolant hose. It carries coolant between the engine and the top of the radiator as part of th...
View full detailsHex Nut - threaded fastener with a six-sided body for a standard spanner or socket.
Stud Bolt for the LT230 transfer box. It clamps a casing joint on the transfer box, securing the main casing and speedometer housing joints.
Rivet used to secure exterior body panels and mouldings, including front wing and body-moulding assemblies. Installed through the panel to retain ...
View full detailsScrew - threaded fastener used in vehicle assembly.
Door Opening Weatherstrip for the front right-hand door aperture. This rubber seal fits around the door opening on the body and seals against the c...
View full detailsDifferential Lock Instruction Label, a self-adhesive label applied to the fuse box cover showing the operating instructions for the differential lo...
View full detailsDifferential Case Shim sets the bearing preload and position of the differential case within the axle. Selective shims of this type are used durin...
View full detailsWarning Label Decal - an adhesive warning label applied to the bodywork. It reproduces one of the factory information and caution labels, restorin...
View full detailsDoor Latch Link Rod for the rear side door latch mechanism. Intermediate link rod that transfers movement within the rear side door between the la...
View full detailsHex Nut, M6. General-purpose metric fastener used at various fixing points across the vehicle.
Locking Wheel Nut Kit for alloy road wheels, part of the road wheel and fixings assembly. Each locking nut replaces a standard wheel nut at one pos...
View full detailsCoin / Package Tray - an open storage tray that fits into the upper facia crash pad, alongside the ashtray assembly.
Package Tray Trim for the facia. Fits into the upper crash pad of the facia (dashboard), providing a stowage tray.
Trim Clip Fir-tree interior trim fastener. The ribbed fir-tree stem pushes into a panel hole to retain interior trim.
Heater Outlet Hose is the coolant return hose from the heater matrix on the 4.0L V8 EFI petrol. It returns coolant from the heater matrix to the e...
View full detailsHeater Inlet Hose is the coolant inlet hose to the heater matrix on the 4.0L V8 EFI petrol. It carries hot coolant from the engine cooling system ...
View full detailsSelector Lever for the manual gearbox gear selection mechanism. It transmits movement from the gear lever to the selector shafts inside the gearbox...
View full detailsRivet - body panel fixing rivet. A blind fastener used to secure body panel and hardware fixings during assembly.
Mounting Bracket - cab body panel fixing bracket. Supports and locates the cab body panel, forming part of the body panel fixing arrangement.
Rear Seat Belt Assembly restrains an occupant in the rear seating area. It comprises the inertia-reel retractor, webbing and latching tongue, moun...
View full detailsSeat Belt
Seat Belt Cover - Upper
Turbocharger Adaptor Pipe in the induction system of the 2.5L 200 TDi and 300 TDi turbo diesel engines. It forms the connecting pipe between the t...
View full detailsFlame Trap, Crankcase Breather for the 3.5L V8 twin carburettor petrol engine. Fitted in the crankcase breather system of the carburettor V8, as l...
View full detailsCoolant Hose for the engine cooling system. The hose routes coolant between cooling-system components and is moulded to suit its position in the c...
View full detailsHose - Radiator
Fuel Filter
Body-to-Chassis Mounting Bracket forming part of the body mounting assembly of the Defender 90, 110 and 130. It provides an attachment point secur...
View full detailsBonnet Release Cable, part of the bonnet latch and release mechanism. The cable connects the interior release lever to the bonnet lock, transmitti...
View full detailsFuel Tank Breather Pipe in the fuel tank ventilation system. It vents the tank to relieve pressure and vacuum during refuelling and use. Fitted to...
View full detailsFixing Screw. A fastening screw used to secure bolt-on accessory fittings to the body, such as roof racks, protection and screen bars, and rear steps.
Fuel Filler Cap for the fuel tank, finished in grey. The cap closes and seals the fuel tank filler neck, retaining fuel vapour and keeping dirt an...
View full detailsO-Ring that seals the oil cooler pipe and hose connections. It provides the seal at engine and transmission oil cooler unions, on manual and autom...
View full detailsSealing washer for a threaded fitting in the engine lubrication circuit. The washer seats under the shoulder of the fitting and is compressed as t...
View full detailsTiming Cover is the front cover plate enclosing the timing drive on the 2.5L 300 TDi turbo diesel. It seals the front of the engine and protects t...
View full detailsGasket seals the joint between the EGR pipe and the inlet manifold. It maintains a gas-tight seal where recirculated exhaust gas enters the inlet ...
View full detailsClutch Slave Cylinder - hydraulic actuator in the clutch release circuit of the 2.4 and 2.2 TDCi diesel engines. Converts hydraulic pressure from ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →