for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Tow Ball 50mm flange-fixing tow ball for use with a bolt-on tow bar drop plate. Rated for a maximum gross trailer weight of 3.5 tonnes, with a D-v...
View full detailsConnecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...
View full detailsMain Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...
View full detailsSnap sac
Steering Damper Assembly for the front axle steering linkage. The hydraulic damper mounts across the steering linkage, where it controls lateral o...
View full detailsBlanking Plug Grommet for the dash assembly. This rubber plug fills an unused aperture in the dash panel - such as the opening for the hand throttl...
View full detailsCrankshaft Oil Seal - Rear - Heavy Duty for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal hou...
View full detailsCrankshaft Oil Seal - Front seals the nose of the crankshaft where it passes through the timing cover on the Td5 2.5L 5-cylinder turbo diesel engin...
View full detailsThis steering drop arm transmits movement from the steering box output shaft to the steering linkage, enabling directional control at the front axl...
View full detailsSplit Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...
View full detailsAlternator for the engine charging circuit, of the Lucas A127 type rated at 45A output. Driven by the auxiliary drive belt from the crankshaft pul...
View full detailsCopper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...
View full detailsBulb 24V 21/5W dual-filament bulb for 24-volt electrical systems. The 21W filament serves the stop light circuit and the 5W filament serves the tai...
View full detailsWasher for the non-hinged windscreen frame assembly. It seats on the frame fixings, spreading the fastener clamp load across the mounting surface ...
View full detailsTank Unit Screw is the slotted cheese-head securing screw for the fuel-tank sender unit. It clamps the fuel-level sender flange down onto the top ...
View full detailsBolt 1/4" UNC x 1-1/4" is a coolant pump fixing bolt used on the 3.5L V8 petrol engine. It secures the coolant (water) pump to the engine within t...
View full detailsIndicator front/rear LED clear lens
Pinion Bearing (Outer) for the Salisbury axle differential. It is the outer of the pair of taper roller bearings that carry the drive pinion, seate...
View full detailsDoor Vertical Filler for the door sealing trim. This vertical rubber filler closes the gap at the rear edge of the front doors and at the front and...
View full detailsExhaust U-Bolt secures a section of the exhaust system to its mounting bracket within the exhaust mounting assembly. The U-shaped bolt passes over...
View full detailsBolt - Torx - Countersunk - Rear Door Hinge is a countersunk Torx-head bolt used to secure the rear side door hinge and check strap. It retains th...
View full detailsBush GENUINE LR sold EACH! for fitting air intake grille 90/110/130 and for fitting old type individual letters "Range Rover"
Banjo Bolt (6mm) for the fuel injector leak-off return circuit on the 200TDi and 300TDi 2.5L turbo diesel engines. The hollow bolt clamps the inje...
View full detailsReverse Light - a 95mm round rear reversing lamp with a clear lens and LED illumination. It forms part of the rear lamp arrangement, projecting wh...
View full detailsFuel Filter Assembly for the Td5 2.5L 5-cylinder turbo diesel fuel system. It filters the diesel supply between the tank and the injection system,...
View full detailsExtended Bump Stops are compression-travel limiters that sit between the axle and the chassis to cap suspension up-travel and cushion the axle agai...
View full detailsAir Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...
View full detailsTiming Belt - toothed camshaft drive belt for the 200 TDi engine. Synchronises the crankshaft with the camshaft and injection pump, holding valve ...
View full detailsPlain Washer - flat washer for use in general fastening assemblies throughout the vehicle. Distributes load and protects mating surfaces under bol...
View full detailsIntermediate shaft lock nut LT230
Wheel Spacer Set, 30 mm: silver alloy wheel spacers for a 5x165 hub, supplied as a set of four with a complete set of wheel nuts. Machined from bi...
View full detailsFront Wheel Arch Kit - extended +30mm width - for Defender 90 and 110, supplied as a pair. Moulded from plastic to closely match the profile of th...
View full detailsRear suspension shock absorber designed to control vertical movement of the axle and dampen spring oscillation within the suspension system. This...
View full detailsHeater to Bulkhead Seal for left-hand drive vehicles, part of the heater and bulkhead assembly. The seal fits between the heater unit and the bulk...
View full detailsMirror Head - 195 mm x 145 mm. The rectangular exterior mirror head that fits the bar-type mirror arm, providing the driver's rearward view along t...
View full detailsHex-head bolt, 7/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and soc...
View full detailsSize/Diameter: 1/4" unf x 7/8"
Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...
View full detailsPan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M6 thread with a 1...
View full detailsIgnition Condenser for the contact-breaker distributor, of the Ducellier type. Wired across the contact-breaker points, the condenser absorbs the ...
View full detailsElectric Fuel Pump mounted externally in the fuel supply system, drawing petrol from the tank and delivering it to the carburettor. This is an ext...
View full detailsHex Nut is a metric M5 hexagonal nut used as a general-purpose threaded fastener across multiple vehicle assemblies. It runs onto a matching M5 ma...
View full detailsLock Nut is a self-retaining fastener used in the door latch and lock mechanism. Part of the door locking hardware, it secures the latch and lock ...
View full detailsRocker Shaft Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the rocker shaft assembly to the cylinder head. It clamps the rocker s...
View full detailsFuel Block Connector for the Td5 2.5L 5-cylinder turbo diesel engine, incorporating the fuel pressure regulator at the fuel block. It forms the ju...
View full detailsCondenser incl. fan Defender
Brake Pipe Union is a male threaded fitting used in the brake hydraulic pipework. It belongs to the brake pipe and fitting group. The union nut th...
View full detailsCLUTCH KIT - COVER + PLATE + BEARING - TD5 - D2/DEF 83-06
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →