for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Lamp Guard for 95mm NAS round lights fitted to Defender models up to 2016. Designed to protect the larger-diameter 95mm North American Specificati...
View full detailsHeater Duct, right-hand side, within the heater demister and air distribution system. Channels air from the heater assembly to the windscreen demi...
View full detailsBearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...
View full detailsHeater To Bulkhead Seal seals the joint between the heater and blower duct and the bulkhead aperture, within the heating and ventilation assembly. ...
View full detailsCrankshaft oil seal Front OEM Puma 2.4 TDCi Puma 2.2 TDCi
Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...
View full detailsCamshaft Cover Retainer for the 2.4L Puma TDCi diesel engine, used to secure the camshaft cover to the cylinder head. It clamps the cam cover down...
View full detailsClutch Driven Plate (235mm) transmits engine torque from the flywheel to the gearbox input shaft within the clutch assembly. The friction plate sp...
View full detailsBrake Pipe Clip - Double - a moulded plastic clip that secures two brake pipes to the chassis within the braking hydraulic circuit. It retains bot...
View full detailsDoor Filler - Top - Front is the horizontal filler strip that runs along the top edge of the front door frame. It closes the channel at the top of...
View full detailsBolt - 5/16" UNC x 4-3/4" is a hex bolt that secures the water pump and power steering pump on the Rover V8 engine. It has a 5/16" UNC thread and ...
View full detailsSteering Shaft is the intermediate steering shaft of the steering column assembly. It transmits steering input from the column down to the steerin...
View full detailsHeater Control Assembly is the dash-mounted control panel for the heating and ventilation system, operating the temperature-blend and airflow setti...
View full detailsIntercooler Hose Kit - Silicone Blue for the turbocharger and intercooler charge-air circuit on the Td5 2.5L 5-cylinder turbo diesel engine. The k...
View full detailsBonnet Buffer Defender 2007 on
Bulb Holder Assembly - Blue for the instrument panel illumination circuit. This holder and bulb assembly fits within the instrument cluster to pro...
View full detailsSpring Washer is a split spring lock washer fitted under a nut or bolt head to maintain clamping tension and resist loosening caused by vibration. ...
View full detailsClutch Cover is the pressure plate assembly of the clutch, bolting to the engine flywheel within the clutch and gearbox coupling. Its diaphragm sp...
View full detailsExhaust Downpipe - De-Cat for the front section of the exhaust system, fitted downstream of the turbocharger outlet on TD5 diesel applications. Th...
View full detailsThis new Terrafirma winch has a powerful 6hp, 12v motor combined with a 3-stage planetary gearbox that gives over 5 tonnes of pulling power. It has...
View full detailsRear Wheel Arch Kit, +30mm wide, supplied as a pair for the rear of the body. The arches extend coverage 30mm beyond the standard profile to suit ...
View full detailsBolt is a general-purpose imperial-thread fixing with a 5/16-inch UNC (Unified Coarse) thread and a 7/8-inch length. Used as a common fastener acr...
View full detailsFront Brake Pad Set - XS for the front braking system, comprising the friction pads that seat in the front calipers. Under hydraulic pressure the ...
View full detailsContact Set for the Lucas distributor fitted to Land Rover petrol engines, comprising the breaker point assembly within the conventional ignition s...
View full detailsWiper Switch - Column is the steering-column stalk switch that controls the windscreen wash/wipe function. Mounted on the steering column, it sele...
View full detailsDrive Belt - the auxiliary (serpentine) drive belt for the 2.4L TDCi (Puma) diesel engine, in the configuration fitted with air conditioning. Driv...
View full detailsLower Strut Gaiter for the rear self-levelling suspension unit. This flexible rubber boot fits over the lower ball joint of the self-levelling str...
View full detailsFront Shock Absorber Turrets: the tubular mounting towers that locate the upper end of the front dampers. Each turret bolts to the chassis and pro...
View full detailsShock Absorber Bush - Rear Upper is the mounting bush at the upper end of the rear shock absorber, where the damper attaches to its body mounting. ...
View full detailsClip Nut spring-steel fastener that provides a captive threaded fixing point on panels and brackets. The nut clips over the edge of a panel or sli...
View full detailsMudflap Bracket for the rear left-hand position, the bracket that mounts the rear mudflap to the body behind the wheel. It holds the mudflap (spla...
View full detailsWing Fixing Plate is a two-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (front...
View full detailsTemperature sensor
Side Step Set is a pair of side steps (running boards) that mount along the lower body sills to aid entry to and exit from the vehicle. Each step ...
View full detailsInjector sealing washer 2.4 Puma
Sleeve OEM
External Circlip for the R380 manual gearbox selector yoke. The circlip locates in the groove on the selector yoke and retains it in position with...
View full detailsPlain Washer is a flat load-spreading washer used in the front axle hub and drive shaft assembly. It sits beneath the retaining fastener to distri...
View full detailsO-Ring - Gear Change Selector seals the gear change selector shaft where it enters the transmission housing, preventing lubricant leakage at the sh...
View full detailsOil Seal for the front cover of the LT85 five-speed manual gearbox. It seals the front cover where the primary (input) shaft enters the gearbox, re...
View full detailsPiston for the 2.25L four-cylinder diesel engine, operating within the cylinder block as part of the piston and connecting-rod assembly. The pisto...
View full detailsOil cooler O-ring V8 small
LED Light Upgrade Kit (deluxe smoked-lens type, 73mm) - a complete set of WIPAC LED lamps with smoked lenses, replacing the original incandescent f...
View full detailsHinge Bolt - M8 x 55 mm Torx-head bolt that secures the side door hinges and door check strap to the body. Fastens the hinge assembly at the door.
Headlamp Bulb - a 24V dual-filament bulb for the main headlamp, rated 55/50W with a P45T base. The two filaments carry the main and dipped beam wi...
View full detailsHigh-Tensile Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/4" shank length. A hex-head fastener manufactured to a high-t...
View full detailsBolt - V8 Inlet Manifold is the fastener that secures the inlet manifold on the Rover V8 petrol engine. It clamps the inlet manifold to the cylind...
View full detailsPlain Washer M8
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →