for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Heater Duct, left-hand side, within the heater air distribution system. Routes air from the heater assembly to the floor-level outlet beneath the ...
View full detailsWater-in-Fuel Sensor for the Td5 2.5L 5-cylinder turbo diesel fuel filter / sedimentor assembly. It threads into the base of the fuel filter housi...
View full detailsFlange Bolt, M8 x 120 mm - a hexagon-head flange bolt that secures the coolant (water) pump on the 300TDi 2.5-litre turbo diesel engine. The integ...
View full detailsNut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.
EGR Valve Gasket seals the exhaust gas recirculation (EGR) valve to its mounting flange within the exhaust gas recirculation circuit. It maintains...
View full detailsSpring Washer for use as a locking fastener component across Land Rover assemblies. A helical split spring washer providing resistance against fas...
View full detailsSpring Ring for the rear self-levelling suspension unit. It seats against the self-levelling strut and locates the coil spring, retaining it correc...
View full detailsDoor Filler is the sloping filler that closes the gap along the angled front edge of the front door. Part of the front door assembly, it seals the...
View full detailsCup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....
View full detailsSloping Panel Filler is the angled filler trim that closes the sloping section at the front of the front-door wind-up window aperture. This is the...
View full detailsBulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...
View full detailsDiff Pinion Taper Roller Bearing is the inner pinion taper roller bearing in the Salisbury axle differential. It supports the pinion shaft where i...
View full detailsSpill Rail for the 300 TDi fuel injection system. The spill rail links the leak-off unions at the top of the injectors and carries surplus fuel fro...
View full detailsBody blanking plug 12 X 18MM
Brake caliper rear RH OEM
Washer for the under-seat fuel tank front mounting assembly. This special-profile washer provides a secure bearing face at the front attachment po...
View full detailsHex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...
View full detailsModular Steel Wheel - Black - 7J x 16 A modular steel road wheel finished in black, sized 7J x 16 with an ET08 offset. The steel construction suit...
View full detailsM12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...
View full detailsColor of the pin may differ.
Front Coil Spring - Heavy Load, Standard Height (Terrafirma). These front coil springs are rated for heavy load while retaining the standard ride ...
View full detailsWater Pump for the 3.5L Rover V8 petrol engine cooling circuit. Belt-driven from the front of the engine, the pump circulates coolant through the ...
View full detailsMirror Glass - the replacement reflective glass for the exterior door mirror. It seats into the mirror head on its backing plate, restoring a clear...
View full detailsTemperature Transmitter is the coolant temperature sender within the engine cooling and instrument gauge circuit, for V8 petrol applications and ca...
View full detailsTiming Belt Tensioner - the tensioner that sets and maintains correct tension on the camshaft timing belt of the 2.5 litre 4-cylinder diesel engine...
View full detailsRear Wheelarch Eyebrow Moulding - Unpainted for the Defender body exterior. This moulding fits over the rear wheelarch aperture, covering the body...
View full detailsHeater Blower Motor for the heater and ventilation assembly. Drives the blower fan that draws air across the heater matrix and distributes it throu...
View full detailsGearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...
View full detailsIntercooler Hose Kit - Silicone Black for the turbocharger and intercooler air circuit on the TD5 2.5L 5-cylinder turbo diesel engine in the Defend...
View full detailsRear Shock Absorber provides damping control within the rear axle spring and damper assembly for suspension set up with extended travel. Twin-tube...
View full detailsFront suspension shock absorber designed to control spring oscillation and maintain tyre contact with the road surface. Twin-tube low-pressure ni...
View full detailsBolt, M10 x 30: high-tensile metric setscrew with an M10 thread, 30 mm long.
Brake Pad Set - Front for the front hydraulic disc brake assembly. The pads are clamped by the caliper against the brake disc to generate friction...
View full detailsMain Bearing Set for the Rover V8 engine, in the standard size. The main bearings are the crankshaft's principal support bearings, sitting between ...
View full detailsSnatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...
View full detailsBrake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...
View full detailsBrake Pad Set - Rear - a set of friction pads for the rear disc brakes, forming part of the rear braking assembly. The pads locate in the rear bra...
View full detailsScrew - No. 8 x 3/4" - a small imperial fixing used to secure the heater control panel to the dashboard. No. 8 gauge with a 3/4" length. Its short...
View full detailsWindscreen Hinge Screw - the fixing that secures the windscreen frame hinge to the bulkhead, allowing the frame to be folded down on models fitted ...
View full detailsGearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...
View full detailsHeater Blower Motor Assembly for the heating and ventilation system, mounted in the heater box. The motor and fan draw air through the heater assem...
View full detailsMain Bearing Set - crankshaft main bearing shells for the 2.25L four-cylinder three-bearing engine. The main bearings support the crankshaft withi...
View full detailsFuel Tank Bolt - a mounting bolt that secures the fuel tank to the chassis. It fixes the tank at its mounting point and is specified for the metal...
View full detailsExhaust Downpipe - LH - V8 is the left-hand front section of the exhaust system on V8 petrol applications. It connects the left-hand exhaust manif...
View full detailsSide Window Seal is the rubber glazing seal that secures and weatherproofs the fixed side window glass within its body aperture. Part of the body ...
View full detailsHeater Demister Hose - ducting hose within the heater demist circuit. Carries warm air from the heater box to the windscreen demister vents.
Bonnet Stay - Classic
Quarter Panel Valance - RH for the Defender 110 Station Wagon. This pressed steel valance panel forms the lower rear section of the right-hand rea...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →