for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...
View full detailsBolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...
View full detailsHeadlamp Pigtail connector lead for the front lighting circuit. The pigtail plugs onto the rear of the headlamp unit and links it to the vehicle's...
View full detailsSpring pin
Upper Brake Pipe for right-hand-drive applications, part of the braking hydraulic circuit. This rigid metal pipe carries pressurised hydraulic flu...
View full detailsHeadlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...
View full detailsWasher for the windscreen and handbrake assembly on Series 2, Series 3, and Military Land Rover vehicles.
Screw
Stud A threaded fastening stud catalogued for use across multiple applications. It is fitted in several locations on the engine and its ancillarie...
View full detailsSac Snap Clip
Belt Tensioner for the V8 EFI petrol engine, part of the ancillary (serpentine) drive belt system. The tensioner pulley bears against the auxiliar...
View full detailsSealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...
View full detailsIndicator Bulb - amber replacement bulb for the exterior indicator lighting circuit. Installs into the indicator lamp housing and provides the amb...
View full detailsLamp Boot - Military is a rubber protective boot for military-specification lamp assemblies. The boot fits over the lamp body to provide a weather...
View full detailsNut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...
View full details7" Round LED Headlights - a pair of sealed LED headlamp units that replace the original sealed-beam or halogen lamps in a traditional 7" round head...
View full detailsAutotec Reverse Light Switch for CDU51/CDU51L manual-gearbox applications. It completes the reverse lamp circuit when reverse is selected. Applica...
View full detailsSwitch - Fuel Tank Tap is an electrical switch used to operate the fuel tap selection on Land Rover Series I, Series II, Series IIA, and Series III...
View full detailsBall Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...
View full detailsBrake Pipe Clip is a retaining clip from the front brake line mounting hardware. The treble form holds three rigid brake pipes side by side at a f...
View full detailsAnti-Roll Bar Fitting Kit - the rear mounting hardware used to install an uprated rear anti-roll bar in the rear suspension. The uprated bar is wi...
View full detailsMounting Plate for the rear door spare wheel carrier assembly. This steel retainer plate secures the spare wheel against the tailgate-mounted spar...
View full detailsGearchange Housing for the LT77 5-speed manual gearbox. Mounted on top of the gearbox, it carries the gear selector mechanism and locates the gear...
View full detailsWheel Arch Kit: a complete set of standard width wheel arches with a matt black finish. The semi-flexible, vacuum-formed plastic arches replace th...
View full detailsRear Wheel Bearing Kit containing the parts needed to overhaul one rear hub bearing assembly. The taper roller bearings carry the rear hub on the s...
View full detailsShock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...
View full detailsFlasher Unit for the direction-indicator circuit, of the 2-pin type without trailer-socket provision. The flasher unit switches the current to the...
View full detailsFront Shock Absorber - hydraulic damper for the front suspension, mounted between the chassis bracket and the front axle. The damper controls the ...
View full detailsFuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...
View full detailsHex Nut - M16 flanged nut with a nylon insert. Used on the rear anti-roll bar mounting pin and on rear suspension knuckle fixings. The nylon colla...
View full detailsCrankshaft Oil Seal - Front - 300TDi
Bolt
Ignition Condenser for the contact-breaker distributor, of the Lucas type, supplied with a long lead (17-7/8 in). Wired across the contact-breaker...
View full detailsAnti-roll bar bush used in the front suspension anti-roll bar assembly, providing the compliant mounting interface between the anti-roll bar and it...
View full detailsValve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...
View full detailsWater Pump Pulley - single-groove V-belt pulley for the water pump on 2.25L and 2.5L 4-cylinder petrol and naturally-aspirated 2.5L diesel engines....
View full detailsSwivel Pin Kit for the upper front axle swivel on ABS applications, serving the top swivel pin that forms the upper pivot between the swivel housin...
View full detailsRear Crossmember Recovery Point - a bolt-on recovery attachment that mounts centrally to the rear chassis crossmember, providing a heavy-duty lashi...
View full detailsMain Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...
View full detailsFiller Strip for the side window aperture of the Defender Station Wagon. Fitted along the window frame opening, the strip fills the gap between th...
View full detailsRepair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...
View full detailsSnap Ring used within the LT95 4-speed gearbox to retain the inner member to the mainshaft. The LT95 is the 4-speed gearbox with integral transfer ...
View full detailsSteering Column Switch
Alternator Mounting Screw for the Rover V8 petrol engine alternator assembly. This screw secures the alternator to its mounting bracket on the eng...
View full detailsBolt - M8 x 40mm standard metric hex-head fastener for use across engine, gearbox, body, and chassis assembly applications.
Strap Stud is a body fixing used in the canvas hood (soft top) and hood frame assembly. It provides an anchor point over which a retaining strap i...
View full detailsCylinder Head to Block Stud for the four-cylinder diesel engines - 2.25L and 2.5L naturally-aspirated. The stud threads into the cylinder block dec...
View full detailsFront Shock Absorber Bush Kit for the front suspension assembly. Bush kit for the front shock absorber mounting, providing the rubber isolation be...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →