for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Injection Pump Pulley is the drive pulley mounted on the input shaft of the mechanical fuel injection pump in the 2.5L 4-cylinder diesel engine. I...
View full detailsCirclip - Bonnet Prop Pin is the retaining circlip that secures the pin on the bonnet prop assembly. The circlip locates in a groove on the prop p...
View full detailsFan
Radius Arm Bush Kit - Chassis End, Front (Terrafirma). A set of four uprated polyurethane bushes for the front radius arm mountings, replacing the...
View full detailsService Filter Kit for the 300 Tdi 2.5L turbo diesel engine, grouping the consumable filters and sealing washers required for a routine engine serv...
View full detailsFlexible Brake Hose for the front hydraulic braking circuit. It carries brake fluid pressure between the rigid chassis-mounted brake pipe and the f...
View full detailsStarter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...
View full detailsShock Absorber - Front - +2" Travel for the front coil spring suspension system, designed for use with a 2-inch suspension lift. The extended-trav...
View full detailsMain Bearing Set for the crankshaft main bearings in the engine bottom end. The bearing shells locate between the crankshaft main journals and the ...
View full detailsWasher is a nylon door hinge washer used on the hinge fixing bolts. It fits over the hinge bolt as a low-friction spacer between the moving hinge ...
View full detailsSuspension Kit providing 2 inches of lift in a medium load configuration, combining rated coil springs with extended-travel Pro Sport shock absorbe...
View full detailsCrown Wheel Bolt - a fastener in the differential final drive assembly of the Land Rover type axle. It secures the crown wheel (ring gear) to the ...
View full detailsLayshaft Bearing for the LT77 and R380 5-speed manual gearbox fitted to the Defender, Discovery 1, Discovery 2, and Range Rover P38. The layshaft ...
View full detailsPhilidas Nut is a 5/16" UNF all-metal self-locking nut. A deformed collar gives it prevailing-torque resistance to loosening under vibration, and i...
View full detailsWood-Rim Steering Wheel, 15" diameter with a semi-dished profile. The wheel mounts to the column through a separate steering boss, which is requir...
View full detailsCrankshaft Pulley Bolt for Land Rover 4-cylinder engines from approximately 1989, used across the Defender, Discovery 1, and Range Rover Classic fi...
View full detailsCarburettor Throttle Linkage Roller for the 3.5L V8 twin-carburettor petrol engine. It runs on the throttle countershaft, guiding the carburettor ...
View full detailsParts Catalogue for the Land Rover Defender, covering 1987 to 2006. This official illustrated reference provides exploded diagrams and part number...
View full detailsIntake to Dump Valve Hose for the 300TDi 2.5L turbocharged diesel engine on the Defender. This hose connects the air intake duct to the dump valve...
View full detailsRoof to Side Seal - Front Upper - LH for the Defender body sealing system. This rubber seal closes the gap between the front upper left-hand edge ...
View full detailsPower Steering Pipe - Pump to Box is the high-pressure hydraulic feed line connecting the power steering pump outlet to the steering box inlet. Th...
View full detailsBolt - M10 double hex - securing the swivel pin housing to the front axle case. This dowel bolt locates and fastens the swivel pin housing to the ...
View full detailsLayshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...
View full detailsspecial bolt for rocker shaft 200 TDI three per engine. sold EACH! - 90/110/130 - Discovery - Range Rover Classic
Roof to Side Seal - Front Upper - RH for the Defender body sealing system. This rubber seal closes the gap between the front upper right-hand edge...
View full detailsOuter Shim - 1.65mm - Front Halfshaft / CV Joint This 1.65mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...
View full detailsABS Wheel Speed Sensor - Front for the 4-wheel ABS braking system. Mounted at the front axle, the sensor reads a toothed reluctor ring and generat...
View full detailsPlastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...
View full detailsStatic Three-Point Seat Belt for the front seating position, combining a lap strap and a diagonal shoulder strap in a single restraint. This is a ...
View full detailsThermostat Housing for the 2.5L 300TDi 4-cylinder turbo diesel engine. This housing secures the engine thermostat within the cooling circuit and f...
View full detailsOil Cooler Seal - seals the oil cooler within the oil cooler and filter assembly. It maintains the oil-side seal between the cooler and its housin...
View full detailsJoint Washer is a sealing washer fitted at a bolted or threaded joint on the 4-cylinder diesel engine, forming a seal between the mating faces to p...
View full detailsInjection Pump Gasket for the fuel injection pump assembly on the 2.5L 4-cylinder naturally aspirated and turbocharged diesel engines. Seals the m...
View full detailsCaged Captive Nut - an M8 nut held in a spring-steel cage that clips into a panel or bracket to provide a captive threaded fixing. It anchors the ...
View full detailsBolt - M8 x 40mm for the front seat rail mounting. This bolt secures the front seat rails to the floor pan. M8 thread, 40mm length. Sold as a sing...
View full detailsSpecial Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...
View full detailsWing Protector - Long - 3mm Aluminium for the Defender front wings. Aluminium chequer-plate protector that mounts over the front wing tops of the ...
View full detailsCylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...
View full detailsO-Ring for the manual air conditioning pipe and hose circuit. This O-ring seals connections within the manual air conditioning pipework, preventin...
View full detailsBanjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...
View full detailsOil Dipstick Tube for the 300 TDi engine, guiding the dipstick down into the sump. Houses and locates the engine oil dipstick, providing the passa...
View full detailsFlywheel Housing Stud for the 2.5L four-cylinder diesel engine. It secures the flywheel housing to the rear face of the engine, locating the housin...
View full detailsSpring Nut - Metal U-Clip for body panel and electrical component fixings across a range of Land Rover models. This metal U-clip spire nut clips o...
View full detailsSedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...
View full detailsPivot Bracket - the pivot bracket for the rear end door check mechanism. The bracket carries the door check arm and its torsion bar, providing the...
View full detailsBearing transfer box OEM TIMKEN
Exhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...
View full detailsPan Head Screw for use in the interior trim and body panel assembly of the Defender 90 and 110. This black-finished self-tapping pan head screw (N...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →