for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...
View full detailsFront Seat Belt, Left-Hand for the front left-hand seating position. It forms part of the vehicle's occupant restraint system. The assembly is an ...
View full detailsFront Seat Belt, Right-Hand for the front right-hand seating position. It forms part of the vehicle's occupant restraint system. The assembly is a...
View full detailsCrankshaft Front Bolt for 2.25L Petrol, 2.5L Petrol, 2.5L Diesel NA and 2.5L Turbo Diesel engines, securing the crankshaft front pulley and timing ...
View full detailsTurbocharger Outlet Gasket for the 2.5L Turbo Diesel and 200TDi engines, sealing the flanged joint between the turbocharger and the exhaust elbow a...
View full detailsManifold to turbo gasket 200TDi
Camshaft O-Ring for the 2.5L four-cylinder diesel engines, including the naturally aspirated diesel, turbo diesel and 200TDi. This O-ring forms th...
View full detailsAir Cleaner Hose for the 2.5L TDi engine air cleaner assembly on the Defender. This hose connects within the air cleaner housing assembly, forming...
View full detailsCylinder Head Gasket for the 2.5L 200/300 TDi turbo diesel engine, sealing the joint between the cylinder head and the engine block. It seals the ...
View full detailsDrive Belt is the serpentine (poly-vee) accessory belt for the 4.0L V8 EFI petrol engine fitted with air conditioning. Driven from the crankshaft ...
View full detailsBoost Pipe Assembly for the 2.5L 300 TDi turbo diesel, part of the turbocharger boost control circuit. It connects the inlet manifold to the injec...
View full detailsPulley
Door Trim Retaining Clip is a cup-type fastener that secures the interior door casing to the door frame. The clip locates in the trim panel and pu...
View full detailsService Kit for the 2.2L Puma TDCi diesel engine - the consumable filters and sump drain plug needed for a routine oil-and-filter service. The kit...
View full detailsClutch Kit renews the friction components of the Td5 driveline clutch and is supplied without the release bearing. The kit comprises the clutch co...
View full detailsCentre Silencer Replacement Pipe occupies the centre section of the exhaust system, replacing the original centre silencer with a free-flowing stra...
View full detailsSwivel Housing Repair Kit renews the front axle steering swivel assembly where the swivel housing has become corroded, worn or is leaking. The swi...
View full detailsSilicone Turbo & Intercooler Hose Kit - a three-piece set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing ...
View full detailsThe Safari Raised Air Intake Snorkel for the Defender TD5/TD4 (1999 Onwards) is engineered for off-road enthusiasts seeking optimal engine protecti...
View full detailsSafari Rear Door Skin - Lower Half. The outer sheet-metal panel for the bottom half of the rear side door (the Safari door), supplied as a repair s...
View full detailsWindscreen Brackets - a pair of CNC-machined billet aluminium brackets with a black anodised finish that secure the windscreen frame at its lower m...
View full detailsScrew - Bonnet Hinge - M6 x 20 for the bonnet hinge assembly on the Defender. This M6 x 20 Torx-head screw secures the bonnet hinge. Used on vehic...
View full detailsHex-Head Bolt with a 7/16" UNF (Unified National Fine) imperial thread and a 2" shank length. A fastener used in the manual steering box mounting ...
View full detailsBolt with a 3/8" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing applic...
View full detailsBolt - M12 x 60mm is a metric hexagon head bolt used across a wide range of assembly applications on Land Rover vehicles. Thread specification M12...
View full detailsBolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...
View full detailsExterior Push-Button Door Handle for the front left-hand door. Mounted on the outer door skin, the handle forms part of the exterior door release ...
View full detailsSteering Wheel Boss is a hub adapter that mounts a replacement steering wheel to the steering column. It engages a 36-spline column shaft and form...
View full detailsLocking Nut for the steering linkage, securing the adjustable joint onto a heavy-duty drag link or steering rod. Once the joint is set to the corre...
View full detailsGlass Retainer Kit for the rear safari door window - the aluminium retaining strips that hold the fixed glass in the door frame. The strips clamp ...
View full detailsPop Rivet - a blind (pop) rivet for fastening panels, trim and seals where access is available from one side only. The rivet is set with a hand or ...
View full detailsRear Stop/Tail Lamp - Red is a 95mm round NAS-style rear lamp serving the combined stop and tail light function. It mounts to the rear body and co...
View full detailsDoor Sill Seal - rear, supplied as a left- and right-hand pair. This rubber seal fits along the rear door sill aperture, forming the weather seal b...
View full detailsFront door latch link
12-Point Bolt for the rear axle assembly on models fitted with the Salisbury axle. Secures a bracket to the axle case. The 12-point head allows a ...
View full detailsSelf-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...
View full detailsScrew - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...
View full detailsOutput Shaft Bearing for the LT76 gearbox, a taper roller bearing that supports the rear output shaft. It locates the output shaft within the gear...
View full detailsPan Head Screw - a 2BA x 1/2 inch slotted pan head fastener used across interior trim and body panel fixings. It retains interior trim panels and ...
View full detailsDrive Belt for the air conditioning compressor, part of the accessory belt drive on the 3.5L V8 petrol engine. The belt transfers drive from the c...
View full detailsBolt & Lockwasher for securing the inlet manifold on the V8 petrol engine. Supplied as a bolt with its matching lockwasher. The imperial 5/16"...
View full detailsEngine Stud - a threaded manifold stud fitted to the exhaust system of the diesel engine. It threads into the cylinder head to provide a fixed anc...
View full detailsBolt
Clutch Cover is the pressure plate assembly of the manual transmission clutch, for V8 petrol applications. It bolts to the engine flywheel and cla...
View full detailsOil Filter Gearbox
Gearbox Gasket for the LT95 four-speed gearbox, sealing the power take-off (PTO) cover joint. Fits between the PTO cover and the gearbox main casi...
View full detailsBall Steel Bearing
Radiator Drain Plug seals the drain point in the cooling system and is removed to drain coolant during flushing or servicing. When fitted it close...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →