for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Hexagonal Plug for the swivel pin housing oil level and drain. This hex-head plug is used in the front axle swivel pin housing as both an oil leve...
View full detailsTrack Rod End for the left-hand side of the steering track rod linkage. The track rod end forms the articulating ball-joint that connects the track...
View full detailsTrack Rod End for the right-hand side of the steering track rod linkage. The track rod end forms the articulating ball-joint that connects the trac...
View full details48 Spline Boss - Defender Fa On
Snorkel Mount is a 3" stainless steel raised air intake that routes engine induction air to a high mounting point, protecting the engine during dee...
View full detailsBrake Pipe - Rear - LH for the rear brake hydraulic circuit. This is a pre-formed rigid brake line for the left-hand side of the rear axle, carryi...
View full detailsWiper Nut is the hex nut that secures the rear-screen wiper arm to its spindle. Part of the rear wiper system, it threads onto the wiper spindle t...
View full detailsInline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...
View full detailsScrew Kit - stainless steel screws for fixing a side air intake grille to the front wing. The set contains five stainless steel screws and serves ...
View full detailsIndicator Lamp - Clear A clear-lens LED rear direction indicator lamp, part of the exterior lighting system. It operates on a 12V supply. The clea...
View full detailsTrim Clip for the door casing. This fastener retains the interior door casing (trim panel) to the door frame, pushing into a locating hole to hold ...
View full detailsCarburettor Seal Kit - SU
Hoodstick Drain Channel forms part of the canvas hood (tilt) framework on Truck Cab and Crew Cab bodies. It runs along the hoodstick assembly to c...
View full detailsHeadlamp Mounting Kit (Black Bezel) - a single mounting assembly for a 7-inch round headlamp unit, forming part of the front lighting installation....
View full detailsExhaust Valve Seat Insert for the cylinder head. The seat insert is pressed into the head to provide the hardened sealing face the exhaust valve c...
View full detailsSynchromesh Assembly - 3rd & 4th is the synchroniser unit for 3rd and 4th gears in the LT77 5-speed manual gearbox. Mounted on the mainshaft b...
View full detailsRear Window Regulator - Right Hand - the mechanism that raises and lowers the rear side door glass on the right-hand side. It mounts inside the re...
View full detailsRelay (yellow) fitted in the under-bonnet fuse and relay box of the vehicle's electrical system. The relay uses a low-current control signal to sw...
View full details30A Maxi Fuse is a circuit-protection device within the vehicle electrical system. The Maxi high-current blade format is rated at 30 amps and is f...
View full detailsBrake Pipe T-Piece is a hydraulic junction in the rear braking circuit, connecting the incoming brake line to the rigid pipes serving the rear whee...
View full detailsFlywheel Timing Pin is a workshop special tool used to lock the flywheel in its reference position when setting the diesel injection pump timing on...
View full detailsFlywheel Timing Pin - an engine timing tool for 4-cylinder diesel engines that locks the flywheel at top dead centre (TDC) so the crankshaft is hel...
View full detailsMain Bearing Set for the 2.25L 4-cylinder petrol and diesel engine, supplied in 0.030" oversize. The main bearings are the replaceable shell beari...
View full detailsTubular Winch Bumper - No Cutting is a tubular steel front bumper assembly for the Defender, replacing the standard front bumper and providing winc...
View full detailsPower Steering Reservoir Cap closes and seals the power steering fluid reservoir in the steering hydraulic circuit. It retains the hydraulic fluid...
View full detailsAccelerator Cable for the 2.25L diesel engine in left-hand drive Defender 110. This cable connects the accelerator pedal to the throttle control l...
View full detailsU-Bolt within the rear door spare wheel carrier assembly. This U-shaped fastener clamps around the spare wheel rim to secure it against the carrie...
View full detailsCrankshaft Starting Dog for the 2.25L 4-cylinder petrol engine fitted to Series III and early Defender models with a 5-main-bearing crankshaft. Th...
View full detailsGearbox Shim for the LT95 4-speed gearbox used in V8-powered Land Rover variants, including Range Rover Classic and early Defender and Series III V...
View full detailsRear Coil Spring for the Defender 110 and 130, rated to standard height and standard load specification. The spring mounts between the rear axle s...
View full detailsWiring Assembly
Washer used as a load-spreading and spacing element within a bolted joint. It seats beneath the bolt head or nut to distribute clamping load over ...
View full detailsWasher – a flat washer used on the 2.5-litre 300TDi turbo diesel engine. The flat washer distributes the clamping load beneath a bolt or nut head.
Seat Belt Assembly - three-point inertia reel front seat belt for the right-hand front seat, part of the occupant restraint system. The inertia re...
View full detailsBrake Hose for the rear hydraulic circuit of Land Rover Defender models without ABS. This flexible rubber hose connects the rigid steel brake pipe...
View full detailsRocker Shaft for the Gemmer manual recirculating-ball steering box, for left-hand drive Defender applications without power steering. The rocker s...
View full detailsOil Temperature Gauge for the instrument cluster of the Defender 90 and 110. The gauge monitors engine oil temperature and provides a continuous a...
View full detailsBattery Condition Gauge for the instrument panel. A 52mm panel-mount gauge that displays battery voltage, providing a direct indication of chargin...
View full detailsRear Folding Step Mat for the rear bumper-mounted folding step assembly on the Land Rover Defender 90 and 110. This rubber anti-slip mat fits the ...
View full detailsSelector Fork for the 5-speed manual gearbox internal gear-change mechanism. The selector fork engages with the synchromesh hub sleeve to move the...
View full detailsThrottle Linkage is a mechanical component in the fuel injection control assembly of the 2.5L 4-cylinder diesel engine. It connects the accelerato...
View full detailsAir Vent Lever Knob for the dashboard air vent mechanism on Land Rover Defender without air conditioning. This knob fits onto the vent control lev...
View full detailsSynchro Ring - 5th Gear - R380 is the baulk ring for the 5th gear synchromesh assembly in the R380 5-speed manual gearbox. The ring equalises the ...
View full detailsClutch Kit 3.9V8 AP
Cylinder Head Gasket Set for the Td5 2.5L 5-cylinder turbo diesel, supplying the ancillary seals and gaskets used around the cylinder head when it ...
View full detailsOil pump pressure relief valve repair kit for the 300 TDi engine lubrication circuit. The pressure relief valve sits in the oil pump housing at th...
View full detailsBolt - M8 x 40. Hexagon-head threaded fastener, M8 x 40 mm, for general assembly and retaining applications. Supplied individually.
Headlamp Assembly for the front lighting system, halogen type. The complete unit houses the main and dipped beam reflector and lens and mounts int...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →