for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Haynes 90/110 workshop man. Diesel only.
Front Door Card is the interior trim panel that covers the inner structure of the front door, concealing the window regulator, latch linkage and wi...
View full detailsSilicone Coolant Hose Kit - replacement coolant hoses for the engine cooling system, for the 300 TDi diesel. This three-piece kit replaces the mai...
View full detailsJack Adapter that provides a secure jacking point for a recovery jack. Bolts into the existing holes under the front bumper and rear crossmember t...
View full detailsSill Protector - Aluminium Chequer Plate for the Defender 90. This aluminium chequer plate protector bolts over the door sill to shield it from sc...
View full detailsBody Seal - Rear Lower - RH Lower rear body seal for the right-hand side. It seals the joint between the lower rear body panel and the adjacent bo...
View full detailsBrake Master Cylinder Repair Kit for the early-type dual-circuit brake master cylinder (NRC8690). The kit restores the sealing and hydraulic funct...
View full detailsManifold Stud is used to secure the combined inlet/exhaust manifold assembly to the cylinder block on Series vehicles fitted with the 2.25L diesel ...
View full detailsSealing Ring - Rocker Cover Breather Bolt for the 2.25-litre 4-cylinder engine. This sealing ring is fitted under the rocker cover breather bolt, ...
View full detailsInterior Lamp Mounting Bracket in the Defender cabin lighting assembly. This bracket mounts the interior roof lamp to the headlining or roof panel...
View full detailsBody Side Steps - a matched pair of fixed side runners for the lower body sides. Mounted along the sill line to the body and chassis fixing points...
View full detailsRoof Centre Console for the Defender Hard Top and Station Wagon interior headlining. The console features a single DIN radio aperture with removab...
View full detailsSide Locker - a stainless steel storage box that mounts in the rear side quarter, set behind the inner rear wheel arch on the left-hand side. The ...
View full detailsSilicone Hose Kit Puma 2.4 - Defender - Blue
Rear Bumper Corners are a pair of heavy-duty wraparound bumperettes that protect the vulnerable rear corners and sill ends of the bodywork. The po...
View full detailsFront Spring Spacers fit between the front axle and the base of the front coil spring to raise the spring mounting point. The spacers are 50mm (2 ...
View full detailsTerrafirma Pro Sport Suspension Kit - Medium Load, +2" (50mm) Lift for Defender 110 and 130. This is a RAISED suspension kit: it lifts the vehicle...
View full detailsSuspension Kit providing 2 inches of lift in a heavy load configuration, combining rated coil springs with All Terrain shock absorbers. The heavy ...
View full detailsTerrafirma All Terrain Suspension Kit - Light Load, +2" (50mm) Lift for Defender 90, Discovery 1 and Range Rover Classic. This is a RAISED suspens...
View full detailsShock Absorber - rear suspension damper with four-stage adjustable damping, for standard ride-height travel. Fitted between the chassis and rear a...
View full detailsShock Absorber - front suspension damper with four-stage adjustable damping, for standard ride-height travel. Fitted between the chassis and front...
View full detailsBig Bore Expedition Shock Absorber - front position, standard ride height. The damper installs between the front axle mounting and the chassis bra...
View full detailsRaised Air Intake relocating the engine air intake to an elevated position at the right-hand A-pillar, drawing clean air from above the wing line. ...
View full detailsRear Coil Spring - Heavy Duty, +2" Lift A rear suspension coil spring from the Terrafirma range, seating between the axle and the chassis spring s...
View full detailsCoil Springs are a matched front pair that raise ride height by 2 inches (50 mm) above standard, forming part of the coil-sprung front suspension. ...
View full detailsCoil Spring - Rear - +2" Light Duty is a rear suspension coil spring providing approximately 50mm (2 inches) of lift above the standard ride height...
View full detailsPast op alle modellen met airco en voorzien zijn van een Superwinch LP of Talon &: Tiger Shark lier tot 12000lbs
Power Steering Box of the Adwest lightweight type, right-hand drive, supplied complete with the drop arm. The steering box is the mechanical heart...
View full detailsFuel Injector Pipe - Cylinder 1 forms part of the high-pressure fuel injection circuit on the 2.5L 200TDi turbo diesel engine. This rigid steel li...
View full detailsWheel Cylinder Brake - RH
Brake servo
Decoke Gasket Set (OEM, Payen) for the 2.5L 300TDi four-cylinder turbo diesel engine. Supplies the gaskets and seals needed to reseal the cylinder...
View full detailsBrake Caliper Piston for the hydraulic disc brake caliper, 46mm diameter and 30.68mm height. The piston sits within the caliper bore and transfers...
View full detailsFusible Link - 100A Blue for the primary electrical protection circuit. A high-current fusible link that installs inline within the wiring harness...
View full detailsdecoke gasket set cylinder head 200TDi engines, WITHOUT head gasket. OEM Elring quality.
Sealing Washer - sump plug sealing washer for the ZF four-speed automatic gearbox. Fitted under the head of the transmission sump drain plug, the ...
View full detailsAllen Head Screw is a body fixing used on the hinged windscreen frame of classic Defender models. The socket (Allen) head allows the screw to be d...
View full detailsFront Brake Hose is the flexible hydraulic hose in the front braking circuit, connecting the rigid brake line on the chassis to the front brake cal...
View full detailsCountersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...
View full detailsRear Brake Caliper Pistons for the rear disc brake caliper. Each piston runs in a caliper bore behind the square-section piston seal and dust boot,...
View full detailsTow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...
View full detailsFront Outer Wing - Aluminium - LH for the Defender 90 and 110, supplying the left-hand front wing panel in the original aluminium construction. Th...
View full detailsFront Brake Caliper, left-hand, for the non-vented (solid disc) front braking circuit. The caliper mounts to the front axle and houses the hydraul...
View full detailsFront Brake Caliper - right-hand side, for the non-vented (solid) front disc installation. The caliper straddles the brake disc and carries the hy...
View full detailsAlternator - belt-driven charging unit of the A133 type, rated at 65 amps. Driven from the crankshaft pulley, the alternator carries the vehicle's...
View full detailsMain Bearing Kit 010 King
Size/Diameter: 1 inch
Piston Ring Set for one piston in the engine's piston and cylinder assembly. The rings seat in the piston ring grooves, sealing combustion pressure...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →