for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Carburettor for the 2.5L petrol engine, mounted on the intake manifold within the fuel delivery system. It meters and atomises fuel into the incom...
View full detailsExhaust Manifold for the 3.5L V8 petrol engine, supplied without heat transfer cover. The manifold collects exhaust gas from one cylinder bank and...
View full detailsValve Spring Cap for the cylinder head valve train. The spring cap seats on top of the valve spring and locates against the split collets on the v...
View full detailsExhaust Downpipe with Cat is the front section of the exhaust system for the 300TDi engine, incorporating the catalytic converter. It bolts to the...
View full detailsHose
Hydraulic Lash Adjuster installed within the valve train assembly of Td5 2.5L 5-cylinder turbo diesel engines, positioned between the camshaft and ...
View full detailsFlywheel Bolt for the 2.5L Td5 five-cylinder diesel engine with manual gearbox. This bolt secures the flywheel to the rear flange of the crankshaft...
View full detailsCam Follower - a roller-type tappet operating in the engine valve train, between the camshaft and the pushrod. It rides on the camshaft lobe and t...
View full detailsOil Pump O-Ring seals the oil pump to the cylinder block in the engine lubrication system. It seals the joint between the pump and its mounting fa...
View full detailsCylinder Head Gasket for the 2.5L 200TDi and 300TDi diesel engines, supplied in the 1.4mm compressed-thickness grade (identified by two holes). Th...
View full detailsInlet Valve operates in the cylinder head valvetrain of the 2.5L 300TDi turbo diesel engine. It seals against the inlet valve seat and opens to ad...
View full detailsThrottle Linkage for the 3.5L V8 fitted with twin Stromberg 175CD carburettors. This linkage connects the throttle pedal input to both Stromberg c...
View full detailsCore Plug seals a casting core hole in the cylinder block, closing off the coolant jacket left open by the casting process. Pressed into the block...
View full detailsLayshaft Nut for the R380 five-speed manual gearbox. It secures the layshaft gear cluster on its shaft, torqued to specification and then staked in...
View full detailsUpgrade your Defender, Discovery 1, or Range Rover Classic with this Cellular Dynamic +2" (50mm Lift) rear shock absorber, engineered for exception...
View full detailsBonnet Sound Deadening Kit - self-adhesive damping material pre-shaped for the underside of the bonnet. Built from a butyl damping layer bonded to...
View full detailsWaterproof Rear Seat Cover Set (Black) - tailored covers for the 60/40 split rear bench seat. Manufactured from hard-wearing woven polyester with ...
View full detailsTow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...
View full detailsRear Window Glass - Heated - With Stop Lamp for the rear door. This heated rear window carries an embedded heating element fed from the heated-rea...
View full detailsDoor Latch Striker Screw - fixing screw that secures the door latch striker to the body pillar. The striker is the catch the door latch engages to ...
View full detailsSeat Belt Reel Assembly - the reel-and-webbing half of a seat belt, within the seat belt restraint system. Supplied as a half belt, it comprises t...
View full detailsFront Seat Base Cover is a replacement upholstery cover for an outer front seat, fitting over the base cushion foam to form the wearing surface the...
View full detailsWindow Regulator Clip is a retaining clip within the side door window regulator assembly. It secures the link between the winder mechanism and the...
View full detailsStud Plate located at the rear end door and rear side door check strap attachment points on the Defender 90/110. Provides the mounting face and ca...
View full detailsDoor Push Button for the exterior handle of the rear side door latch assembly. Releases the latch when depressed, opening the door from the outside...
View full detailsDoor Assembly is the complete right-hand rear side door shell. The one-piece door is built as an aluminium skin over a steel frame and is supplied...
View full detailsSwivel Shackle - a shackle with an integrated rotating swivel. The swivel lets the connected component turn freely relative to the anchor point, p...
View full detailsAlleen geschikt voor OEM High-Lift jack (ARB) NIET voor Jackall/T-max. Voor Jackall / T-Max gebruik: BA 185A (DA4059)
Sill Protector Pair - exterior body protection panels that fit along the lower sill (rocker) sections beneath the doors. Supplied as a matched lef...
View full detailsRock Sliders - bolt-on sill protection bars that run along the lower body between the wheel arches, shielding the sills and lower chassis edge from...
View full detailsFront Fender - Defender - RH
Reservoir bracket
NAS Stop / Tail Light - LED Clear - a single LED rear stop and tail lamp with a clear lens, designed to NAS (North American Specification) lamp dim...
View full detailsBody Seal - Rear Lower - LH Lower rear body seal for the left-hand side. It seals the joint between the lower rear body panel and the adjacent bod...
View full detailsSpire Nut (U-type spire fastener) for trim and panel fixings. Spring-steel push-on nut that clips over a panel edge or stud to provide a captive f...
View full detailsSelf-Tapping Screw - a No. 6 x 1/2" imperial self-tapping fixing used as a general-purpose fastener throughout the body and chassis. The self-tapp...
View full detailsScrew for use in Land Rover body, chassis, and hardware applications.
Nutsert - 1/4" UNF is a blind rivet nut (rivnut) with a 1/4" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal or...
View full detailsAutogear Power Syn 75W90 5L
Rear Axle Case Bolt for the Salisbury rear axle. The bolt clamps the axle casing joint of the Salisbury (heavy-duty) rear axle, keeping the housin...
View full detailsFront Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...
View full detailsValve Guide for the Rover V8 cylinder head. Pressed into the cylinder head, the guide supports the valve stem and keeps the valve concentric with ...
View full detailsO-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...
View full detailsPrimary Pinion Shim - 2.00 mm for the four-speed V8 gearbox. Used during gearbox assembly or rebuild to set the correct end-float and bearing prel...
View full detailsHose
Ignition Switch for the steering-column lock, diesel specification. The switch is the electrical unit that fits into the steering-column lock barre...
View full detailsRear Halfshaft for the Salisbury rear axle, 24-spline, right-hand side. The halfshaft transmits drive from the differential through the axle casin...
View full detailsSpring Pin for the LT95 four-speed gearbox, used in the gear selector mechanism. The hollow, sprung roll pin locates and retains selector componen...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →