for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Number Plate Lamp - LED is the rear licence plate illumination unit within the rear lighting circuit. It mounts above the licence plate at the rea...
View full detailsStainless Steel Braided Brake Hose Kit - Goodridge flexible brake hoses supplied 2in longer than standard for vehicles running a suspension lift. ...
View full detailsSpare Wheel Cover - 235/85 R16 - vinyl cover for an externally mounted spare wheel, sized to a 235/85 R16 tyre. The cover pulls over the assembled...
View full detailsLED Side Repeater Lamps - Amber - a pair of sequential (dynamic) LED repeaters with an amber lens for the front wing side repeater positions in the...
View full detailsTop Shock Bush Kit - replacement upper mounting bushes for Pro Sport and 8-stage adjustable remote reservoir shock absorbers. The bushes seat in t...
View full detailsLED Side Repeater Lamps - Clear - a pair of sequential (dynamic) LED repeaters for the front wing side repeater positions in the exterior lighting ...
View full detailsLED Side Repeater Lamps - Smoked - a pair of sequential (dynamic) LED repeaters with a smoked lens for the front wing side repeater positions in th...
View full detailsShock Ball Joint Kit - service kit for the spherical mounting joint at the end of a performance shock absorber. The ball joint is the principal we...
View full detailsAnti-Roll Bar Bush in polyurethane, 25.4mm bore, for the rear anti-roll bar mounting. The bush sits where the bar is clamped to its chassis bracke...
View full detailsTF Wing Top Foam Gaskets - 07 On
Plain Washer - flat steel washer from the hardware and fixings group. It is fitted under a bolt head or nut to spread the clamp load over the join...
View full detailsWind Deflectors - Rear - Defender
Universal Joint - replacement universal joint for wide angle and double cardan propshaft assemblies in the driveline. Sits between the propshaft y...
View full detailsReceiver Hitch Pin - retaining pin for a 2in receiver hitch assembly. The receiver housing has a 2in internal bore that accepts a 2in square-secti...
View full detailsGoodridge Brake Hose Kit - +2"
Stainless steel braided brake hose kit, three-line, +2" extended length. The flexible hoses carry hydraulic pressure across the moving joint betwee...
View full detailsAnti-Roll Bar Fitting Kit - Front
Extreme Rear Body Corners - Pair - 90
Gear Lever and Transfer Box Lever Knob Set in polished alloy with a silver finish, replacing the standard plastic knobs on the main gear lever and ...
View full detailsInternal Spacer for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The spacer fits inside the bump stop to shorten the ...
View full detailsDamper Rod - replacement 12" shaft for the 2.5" smooth-body competition damper (TF488), supplied as a rebuild service part. The rod carries the pi...
View full detailsValve for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The TF140 is a monotube, nitrogen-charged unit adjustable betw...
View full detailsSeal Kit - Bump Stop
Nylon Pad for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The pad forms the contact face at the end of the bump stop...
View full detailsSwitch mounting bracket for a single differential lock switch, forming part of the electric locking differential control circuit. The bracket give...
View full detailsSeal Kit - 11" Travel Shock
Replacement Damper Shaft for the 11 inch travel Mega Sport monotube shock absorber. The shaft carries the damping piston and passes through the se...
View full detailsSwitch mounting bracket for two differential lock switches, forming part of the electric locking differential control circuit. The bracket gives b...
View full detailsPanhard Rod Bush Kit - replacement polyurethane bush set for heavy-duty adjustable Panhard rods, within the axle lateral-location assembly. The Pa...
View full detailsOff-Road Foam Air Filter Element for the air box in the engine induction system, dimensioned to sit in the standard housing in place of the paper e...
View full detailsFoam Air Filter - Snorkel Filter - TD5
Bump stops, standard height - front or rear axle. The bump stop absorbs the last part of suspension compression, cushioning axle-to-chassis contac...
View full detailsFoam Air Filter - Defender 300TDi
Receiver Hitch Pin - the retaining pin for the integrated 2" receiver hitch on the TF883NAS rear step tow bar assembly. The pin passes through the...
View full detailsFuel Cooler Guard - an underbody protection plate for the diesel fuel cooler in the fuel supply and return circuit. The fuel cooler is mounted ben...
View full detailsO-Ring - replacement seal for the heavy-duty drive flange centre nut. The O-ring seats between the drive flange body and its removable threaded ce...
View full detailsFront Radius Arm Bush Kit - Axle End - a set of four polyurethane bushes for the axle-end mounting eyes of the front radius arms, within the front ...
View full detailsTRED Bumper Spot Light Brackets - stainless steel spotlight mounting brackets, supplied as an optional extra for the TRED winch bumper range. The ...
View full detailsFuel Filler Surround Plate - a chequer plate panel framing the fuel filler aperture in the rear body side, within the exterior body protection asse...
View full detailsFuel Filler Surround Plate - a chequer plate panel framing the fuel filler aperture in the rear body side, within the exterior body protection asse...
View full detailsFuel Filler Surround Plate - a chequer plate panel framing the fuel filler aperture in the rear body side, within the exterior body protection asse...
View full detailsFuel Filler Surround Plate - a chequer plate panel framing the fuel filler aperture in the rear body side, within the exterior body protection asse...
View full detailsScrew - threaded fastener specified in two unrelated assemblies: securing components to the cylinder block of the 2.5L 5-cylinder turbo diesel engi...
View full detailsHex Socket Screw, M8 x 20 - hexagon socket head fixing screw. Used on diesel engine installations at points where a conventional hexagon head cann...
View full detailsPiston Ring Set - 0.020in Oversize - 300TDi
Hex Head Bolt is a hexagonal-head threaded fastener used as a mounting bolt on the vehicle. It is driven with a standard hexagonal socket or spanner.
Distributor Cap for the ignition distributor assembly on the Rover V8 petrol engine. The cap locates over the distributor body and carries the eig...
View full detailsBrake Caliper Repair Kit for the rear brake caliper assembly - a piston seal kit for renewing the caliper's hydraulic sealing at the piston bore. ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →