for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...
View full detailsGasket Sealant - a non-setting jointing compound to the Hylomar 2000 specification, used on engine and transmission joint faces where a liquid seal...
View full detailsBung - Rear Step - replacement rubber bung for the NAS-pattern rear step assembly. The bung plugs the aperture in the step body, closing it agains...
View full detailsSide Sill Protectors - Chequer Plate, supplied as a left- and right-hand pair for the outer body sill panels beneath the door apertures. Pressed f...
View full detailsRetaining Washer for the rear shock absorber top mount. The rear damper is located at its upper eye by rubber bushes clamped between washers on th...
View full detailsService Kit - Major - Td4 2.2 Diesel
Oil Pressure Switch for the Rover V8 engine lubrication circuit. The switch threads into the engine oil gallery and closes below its set pressure ...
View full detailsRear Shock Absorber - hydraulic telescopic damper for the rear coil-sprung suspension, mounted between the axle bracket and the chassis mounting tu...
View full detailsRear Shock Absorber - hydraulic telescopic damper for the rear coil-sprung suspension, mounted between the axle bracket and the chassis mounting tu...
View full detailsMajor Service Kit for the 2.5L naturally aspirated and 2.5L turbo diesel (19J) engines, grouping the filtration and sump sealing items renewed at a...
View full detailsContact Breaker Set for the Ducellier distributor fitted to the 2.25-litre four-cylinder petrol engine. It is the mechanical switch in the ignition...
View full detailsMain Bearing Set for the crankshaft main journals of the 2.5 litre four-cylinder diesel engine (naturally aspirated, turbo diesel, 200 Tdi and 300 ...
View full detailsMain Bearing Set, standard size, in copper-lead bearing material, for the crankshaft main journals of the 2.5 litre four-cylinder diesel engine (na...
View full detailsDistributor Setscrew is the clamping fastener for the distributor within the ignition system of the 3.5L V8 twin-carburettor petrol engine. It sec...
View full detailsBrake Pipe T-Piece is a hydraulic junction in the rear braking circuit, connecting the incoming brake line to the rigid pipes serving the rear whee...
View full detailsTouch-Up Paint Pencil in County Red, colour code LRC467, for repairing stone chips, small scratches and other localised damage to the paint finish....
View full detailsBig End Bearing Set - a set of connecting rod (big end) bearing shells for the Td5 2.5L 5-cylinder turbo diesel engine, supplied in 0.010 in oversi...
View full detailsMain Bearing Set - a complete set of crankshaft main bearing shells for the Td5 2.5L 5-cylinder turbo diesel engine, supplied in 0.020 in oversize....
View full detailsBig End Bearing Set - a set of connecting rod (big end) bearing shells for the Td5 2.5L 5-cylinder turbo diesel engine, supplied in 0.020 in oversi...
View full detailsMain Bearing Set for the crankshaft main journals of the Td5 2.5L 5-cylinder turbo diesel engine, in 0.010 in oversize. The shells locate in the c...
View full detailsBanjo Bolt for the injector leak-off connection on the 2.5L 200 TDi and 300 TDi turbo diesel engines. The bolt passes through the eye of the leak-...
View full detailsFuel Shut-Off Solenoid for the rotary fuel injection pump on the 2.5L 300 TDi turbo diesel engine. The solenoid threads into the pump head and con...
View full detailsCeramic Rear Brake Pads for the rear disc brake assembly. The pads are clamped by the caliper pistons against the disc faces to generate braking t...
View full detailsCeramic Front Brake Pads for the front disc brake assembly, specified for solid (non-vented) front discs. The pads are clamped by the caliper pist...
View full detailsBrake Pad Set - Front - friction pads for the front disc brake caliper assembly, for the solid (non-vented) front disc installation. The pads loca...
View full detailsRear Brake Pads - Ceramic Rear axle disc brake pads, part of the rear braking assembly. The pads are carried in the rear caliper and are clamped a...
View full detailsFront Brake Pads - Ceramic Front axle disc brake pads for vented front discs, part of the front braking assembly. The pads are carried in the fron...
View full detailsBumper Tread Plates - tread panels for the upper faces of the front bumper, supplied as a pair. They provide a non-slip standing surface when work...
View full detailsWindscreen Washer Pump - the electrically driven pump for the windscreen and backlight wash system. The pump mounts to the washer reservoir and dr...
View full detailsScrolling LED Indicators - 95mm - Rear - Smoked - a set of 95mm scrolling indicator lamps with smoked lenses for the rear indicator positions in th...
View full detailsRestrictor
Differential Guard - 5 mm steel underbody guard that shields the differential housing and nose-piece from impact damage on rock and rutted ground. ...
View full detailsAerosol Paint - Coniston Green Solid (570) is a ready-to-use aerosol in the factory body colour Coniston Green, colour code 570. Intended for touc...
View full detailsWiper Blade - replacement blade for the wiper system. The blade fits to the wiper arm and carries the rubber wiping element that clears the glass....
View full detailsExhaust Valve for the cylinder head of the 2.4 Td4 diesel. Seals the exhaust port against combustion pressure and releases the spent gases into th...
View full detailsFront Bumper Tread Plates - chequer plate covers for the upper face of the front bumper, within the exterior body protection assembly group. Suppli...
View full detailsScrolling LED Indicators - 95mm - Rear - Clear - a set of 95mm scrolling indicator lamps for the rear indicator positions in the exterior lighting ...
View full detailsUniversal Joint for the propeller shaft, measuring 75 mm across the bearing caps with a 27 mm cap diameter. Sealed type, supplied without a grease ...
View full detailsBody Seal - Lower Rear - RH seals the joint between the rear body tub and the upper body panel at the lower right-hand rear corner. It closes the ...
View full detailsTiming Cover Oil Seal is the front crankshaft oil seal, located in the timing gear cover. It seals around the crankshaft where it passes through t...
View full detailsValve Stem Seal for the cylinder head of the 2.2L Td4 Diesel engine. The seal fits over the valve stem at the valve guide, controlling oil entry a...
View full detailsValve Stem Seal for the cylinder head of the 2.2L Td4 Diesel engine. The seal fits over the valve stem at the valve guide, controlling oil entry a...
View full detailsGasket - Cylinder Head Front Cover
Gasket - Cylinder Head Front Cover
Door Lockface Gasket for the side door latch mechanism. It seals the interface between the latch (lock face) and the door shut face, keeping water ...
View full detailsCamshaft Position Sensor for the 2.2L turbo-diesel engine. The sensor monitors the position of the camshaft and signals the engine control unit, w...
View full detailsConnecting Rod Bearing Set supplies the big-end bearing shells that run between the connecting rods and the crankshaft crankpins. Machined 0.020in...
View full detailsConnecting Rod Bearing Set supplies the big-end bearing shells that run between the connecting rods and the crankshaft crankpins. Machined 0.010in...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →