for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Front Brake Pad Set - friction pads for the front disc brake assembly. Each pad is friction material bonded to a steel backing plate. The pads loc...
View full detailsSilicone Turbo and Intercooler Hose Kit for the 2.2L TD4 turbo diesel charge-air circuit, covering the hose runs between the turbocharger, the inte...
View full detailsComplete Piston for the engine crankshaft and piston assembly, supplied with the piston, gudgeon pin and rings. This is a +05 oversize piston, int...
View full detailsMud Deflector Set - four moulded deflectors covering the front and rear arches of a long-wheelbase body. Each deflector closes the open gap betwee...
View full detailsFront Brake Pad Set - friction pads for the front disc brake assembly. Each pad is friction material bonded to a steel backing plate. The pads loc...
View full detailsRear M Flap Brkts - Black - Pair - 90
Oil Level Sensor mounts in the engine oil pan (sump) and measures the engine oil level, reporting it to the instrument cluster oil-level indicator....
View full detailsRear Chassis Cross Member Plate - a chequer plate cover for the exposed rear face of the chassis cross member, within the exterior body protection ...
View full detailsRoof Rack Rail Assembly - Rear - the rear rail of the bolt-together roof rack support frame, forming part of the rack's upper mounting frame. The ...
View full detailsRear end door card in black - the interior trim casing for the rear door. It covers the inner door skin and gives the rear door a finished interior...
View full detailsBrake Pad - friction pad for the rear disc brake assembly, in the version without a wear-indicator sensor. The pad locates in the rear caliper and...
View full detailsCoil Springs - Front, 1" lowered, supplied as a pair. Standard-rate springs for the front coil suspension, reducing front ride height by 1". They ...
View full detailsDisc - Brake - Pair
Synchro Spring Ring from the mainshaft synchroniser assembly of the R380 five-speed manual gearbox. The spring ring sits within the synchroniser h...
View full detailsClutch Plate
Locking Wheel Nut Kit - a set of five locking wheel nuts in a black finish, fitted in place of standard wheel nuts to secure the road wheels to the...
View full detailsRear Mudflap Brackets - Pair - 110 130
Wing Mirror with LED Light - a pair of replacement exterior mirror heads with an integrated LED lamp, supplied as a matched left and right set. Th...
View full detailsRear Brake Discs supplied as a matched pair are solid (non-vented) rear brake discs for models without ABS. Each disc mounts to the rear hub and p...
View full detailsSynchromesh Assembly First/second gear synchromesh assembly for the LT95 four-speed gearbox. Synchronises shaft and gear speeds during 1st-to-2nd ...
View full detailsFront Brake Pad Set - friction pads for the front disc brake assembly. Each pad is friction material bonded to a steel backing plate. The pads loc...
View full detailsSelector Fork for 3rd/4th gear selection in the 5-speed manual gearbox (LT77/R380). The fork engages the synchroniser sleeve and slides it along t...
View full detailsLower Engine Gasket Set for the Td5 2.5L five-cylinder turbo diesel engine. Contains the gaskets used when working on the lower half of the engine...
View full detailsRear Relocation Cones - Axle - Pair
Rear Relocation Cones - Axle - Pair
Lucas Reverse Light Switch for CDU51/CDU51L manual-gearbox applications. It completes the reverse lamp circuit when reverse is selected. Applicati...
View full detailsTowing Bracket Slider is the adjustable-height slider plate for the Dixon Bate adjustable towing bracket, setting the height at which the coupling ...
View full detailsBeck B Plate Clutch
Brake Pad - rear axle friction pad for the rear disc brake assembly. Hydraulic pressure at the caliper piston clamps the pad against the brake dis...
View full detailsBlanking Plug with a chrome finish, an interior trim fitting for the cigar lighter aperture. It fills the cigar lighter / 12V accessory socket ope...
View full detailsFuel Filter Kit - an in-line fuel filter service and conversion kit for the V8 EFI petrol fuel supply. The in-line filter mounts between the fuel ...
View full detailsABS Sensor Seal for the anti-lock braking system. The seal fits at the ABS sensor location, sealing the sensor bore against fluid and contaminatio...
View full detailsScrolling LED Indicators - 73mm - Front and Rear - Amber - a set of 73mm scrolling indicator lamps with amber lenses for the front and rear indicat...
View full detailsScrolling LED Indicators - 73mm - Front and Rear - Clear - a set of 73mm scrolling indicator lamps for the front and rear indicator positions in th...
View full detailsScrolling LED Indicators - 73mm - Front and Rear - Smoked - a set of 73mm scrolling indicator lamps with smoked lenses for the front and rear indic...
View full detailsOil Filler Cap for the Td5 2.5L 5-cylinder turbo diesel engine. Machined from aluminium with a blue anodised finish and fitted with a rubber sealin...
View full detailsCamshaft Sprocket is the camshaft drive gear within the timing drive assembly. Mounted on the camshaft, it is driven by the timing chain to keep v...
View full detailsCamshaft Sprocket is the camshaft drive gear within the timing drive assembly. Mounted on the camshaft, it transfers drive from the timing drive t...
View full detailsXS-Style Wing Mirror Head in gloss silver, supplied complete with the mirror glass and rubber surround. It replaces the head only and clips onto th...
View full detailsBasic Coloured Light Kit 73mm
Emergency Bulb and Fuse Kit - 12 volt, for vehicles using H4 headlamp bulbs. A compact set of replacement bulbs and fuses to carry in the vehicle,...
View full detailsAshtray in Ebony Black for the centre floor console. The ashtray is a removable insert that locates in the console cubby box.
Gearbox Breather Tube Assembly vents the manual transmission casing. Fitted to the MT82 six-speed manual gearbox, the tube equalises internal air ...
View full detailsSeal Assembly - Oil
Drain Plug for the MT82 6-speed manual gearbox. It seals the oil drain and filler opening in the manual transmission case and is removed to drain ...
View full detailsOil Gallery Plug for the MT82 6-speed manual gearbox. A threaded plug that closes an oil gallery and access hole in the manual transaxle case, sea...
View full detailsDrain Plug for the MT82 6-speed manual gearbox. It seals the oil drain and filler opening in the manual transmission case and is removed to drain ...
View full detailsBlanking Plug for the MT82 6-speed manual gearbox. A threaded plug that closes an access opening in the manual transmission case, sealing the casi...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →