for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Brake Pad - Rear is a set of disc brake friction pads for the rear axle. The pads are clamped against the brake disc by the caliper to generate br...
View full detailsBall Joint Boot Clip retains the protective boot over the rear A-frame ball joint. It holds the ball joint boot in place on the rear A-frame (Watt...
View full detailsSteering Wheel Boss for fitting an aftermarket steering wheel to a 48-spline steering column. This hub adapter converts the splined column to the ...
View full detailsRear brake pads for the rear disc braking assembly. The pads are carried in the rear caliper and are clamped against the brake disc to generate br...
View full detailsFront Brake Pads for the front disc brake assembly. The pads locate in the front brake caliper and are clamped against the brake disc when hydraul...
View full detailsAcme Thread Screw for the front wing assembly, part of the body panel fixing hardware. The hex-head screw uses a coarse Acme thread form that bite...
View full detailsRear Brake Pad Set - friction pads for the rear disc brake assembly. The pads sit in the caliper on either side of the brake disc. When the hydrau...
View full detailsWorkshop Manual for the Puma-generation diesel Defender, published by Haynes. This printed manual provides step-by-step routine maintenance, servi...
View full detailsFront Seat Belt Assembly, right-hand, long-end, part of the front seat belt and restraint assembly. This is the long-end half of the front belt - ...
View full detailsFront Seat Belt Assembly, left-hand, long-end, part of the front seat belt and restraint assembly. This is the long-end half of the front belt - t...
View full detailsSide Step End Caps - a set of eight replacement end caps that close the open ends of twin-tube side step assemblies. These caps fit the twin-tube ...
View full detailsBrake Pad Set - front axle friction pad set for the front disc brake calipers, covering both sides of the vehicle. Each pad sits in the caliper ca...
View full detailsBrake Pad Set - replacement friction pads for the front disc brake calipers, supplied as a complete axle set. The pads locate in the caliper carri...
View full detailsBrake Pad Set - rear axle friction pad set for the rear disc brake calipers, covering both sides of the vehicle. The pads are held in the caliper ...
View full detailsBrake Pad Set - replacement friction pads for the rear disc brake calipers, supplied as a complete axle set. The pads locate in the caliper carrie...
View full detailsBrake Pad Set - Front - front service brake assembly, supplied as a complete axle set for both front wheels. The pads carry the friction material ...
View full detailsRetrim Kit - Black - Centre Seat
Grille Heater Inlet Stainless Screws x 7 - set of seven stainless steel screws for the wing-top heater air intake grille and the bonnet vent panels...
View full detailsStay, Floor to Sill. Rear body lower mounting bracket. It braces the rear body floor down onto the sill, carrying load from the floor panel into t...
View full detailsBonnet Prop Rod, scissor type. Part of the bonnet and hinge assembly, it holds the bonnet in the raised position and folds flat against the bonnet ...
View full detailsCable Nipple for the automatic transmission gearchange cable. The nipple is the small end fitting secured to the selector cable, forming the conne...
View full detailsDifferential Lock Spring for the LT230 transfer box. It provides the spring load in the front output shaft centre differential lock mechanism, retu...
View full detailsScrew - threaded fastener used in vehicle assembly.
Depression Control Valve, Td5
Front Stop Bolt
Brake Limiting Valve - hydraulic pressure-limiting valve in the brake pipe run, fitted only to vehicles built without an anti-lock braking system. ...
View full detailsFifth Speed Gear - 19-tooth 5th driven gear for the R380 five-speed manual gearbox. Mounts on the mainshaft and meshes with the layshaft to provid...
View full detailsSpeedometer Drive Gear for the LT230 transfer box. Driven gear that picks up transfer box output-shaft rotation to drive the speedometer, with 20 ...
View full detailsClutch Release Spirol Pin is a coiled spring (spirol) roll pin used in the clutch release mechanism. It locates and retains the release fork again...
View full details2nd Speed Gear for the R380 five-speed manual gearbox. It runs on the mainshaft as part of the first/second gear cluster, meshing with the layshaft...
View full detailsCross Pin for the LT230 transfer box centre differential. This one-piece heavy-duty cross pin (differential spindle) carries the centre-differenti...
View full detailsFront Brake Disc - Ventilated, supplied as a pair. Ventilated front brake discs for the front axle brake assembly. Internal vanes between the two ...
View full detailsSlave Cylinder Push Rod transmits the clutch slave cylinder output to the clutch release fork. As the hydraulic slave cylinder extends, the push r...
View full detailsFront Indicator Bulb - PY21W amber signal bulb, 12V 21W, with a BAU15s offset-pin bayonet base. It fits the front direction indicator lamp. The am...
View full detailsGearbox Oil Seal seals the bell housing of the R380 5-speed manual gearbox. Running on the input shaft at the front of the gearbox, it retains tra...
View full detailsClutch Slave Cylinder Push Rod transmits movement from the hydraulic slave cylinder to the clutch release lever. As the slave cylinder extends, th...
View full detailsSpacer - mainshaft gear spacer for the manual gearbox. It sets the axial spacing of the gears along the gearbox mainshaft, maintaining correct gea...
View full detailsNylon Washer for the interior and exterior mirror mountings. The washer sits between the mirror arm or bracket and its mounting face, spacing the ...
View full detailsDifferential Lock Ring for the LT230 transfer box. It operates on the front output shaft as part of the centre differential lock mechanism, engagin...
View full detailsOil Pump Bolt - a fixing bolt in the engine lubrication system, securing the oil pump to the cylinder block. Used on the 2.5L 5-cylinder Td5 turbo...
View full detailsSynchromesh Assembly is the 3rd/4th gear synchroniser assembly for the 5-speed manual gearbox. Mounted on the mainshaft, it synchronises shaft spe...
View full detailsFlanged Screw - threaded fastener with an integral flange head that spreads the clamping load, used in vehicle assembly.
Thrust Washer and Pin for the LT95 four-speed gearbox, 3.79mm thickness. This selective-thickness washer, with its locating pin, sets the end-float...
View full detailsDifferential Lock Selector Fork for the LT230 transfer box. It acts on the front output shaft differential lock sleeve, translating selector moveme...
View full detailsRear Brake Disc is a solid (non-vented) rear brake disc for models without ABS. The disc mounts to the rear hub and provides the friction surface ...
View full details5th Speed Gear for the LT77 five-speed manual gearbox in V8 applications. The 85mm driven gear for fifth speed, running on the gearbox mainshaft t...
View full detailsPanel Assembly - Door Lower
Rear Suspension Damper - hydraulic shock absorber for the rear suspension of the long-wheelbase (110-inch and 130-inch) chassis. It damps the oscil...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →