for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Rear Side Door Glass for the right-hand side, glazing the rear side door. Clear (untinted) glass, 4mm thickness.
Swivel Pin Housing for the front axle steering swivel assembly, right-hand side, left-hand drive applications. The housing pivots on the swivel ba...
View full detailsSeat Belt Assembly for the right-hand rear seating position, part of the occupant restraint system. The assembly provides the inertia-reel retract...
View full detailsBolt, M10 x 45 mm, securing a mounting bracket to the chassis. A threaded fastener with a 10 mm metric thread and a 45 mm shank length. It forms t...
View full detailsValve Spring - V8 is a cylinder head valve spring for the Rover 3.5L and 3.9L V8 petrol engine. The valve spring seats between the cylinder head a...
View full detailsFront Propshaft - Double Cardan - a complete front propeller shaft assembly running between the transfer box front output flange and the front diff...
View full detailsFront Seat Belt - Left-Hand - Red - a front left-hand (nearside) seat belt assembly finished in red, replacing a worn, faded or damaged original fr...
View full detailsSoft Top Finisher for the right-hand rear quarter panel, part of the soft top body trim. Fits the rear quarter section on the RH side to finish th...
View full detailsBody Seal - Rear Upper for the left-hand side of the rear body section, part of the body sealing assembly. Fitted along the upper edge of the rear...
View full detailsBody Seal - Rear Upper for the right-hand side of the rear body section, part of the body sealing assembly. Fitted along the upper edge of the rea...
View full detailsPlain Washer (M10) for use at the fuel tank mounting points on Series, Defender, and Range Rover Classic vehicles. Fitted beneath the mounting bol...
View full detailsBanjo Bolt for the clutch hydraulic circuit, at the master cylinder pipe connection. This hollow bolt secures the banjo fitting of a clutch hydrau...
View full detailsTow Rope Recovery towing rope for on- and off-road vehicle recovery, connecting a casualty vehicle to a recovery vehicle. It is supplied with a st...
View full detailsFront Axle Differential Casing for the front drive axle. This casting forms the central housing of the front axle. It carries the differential cro...
View full detailsSelector Illumination Bulb Wedge-type (capless) bulb that illuminates the gear selector indicator. It seats in the selector mounting assembly behi...
View full detailsPro Sport Light Load Suspension Kit providing approximately 2 inch (50 mm) of lift across the front and rear suspension. The kit comprises light-l...
View full detailsAll Terrain Heavy Load Suspension Kit providing approximately 2 inch (50 mm) of lift across the front and rear suspension. The kit comprises heavy...
View full detailsSimulated Beadlock Wheel - an 8x16 steel road wheel fitted with a simulated (replica) beadlock outer ring. Rim specification: 16 in diameter, 8 in...
View full detailsCup Washer Cup-shaped washer for the ABS modulator mounting within the anti-lock braking system. It seats over the modulator's rubber mounting bus...
View full detailsFront Cover Gasket sealing the engine front cover to the cylinder block on the V8 EFI petrol engine. The gasket forms the joint between the timing...
View full detailsSliding Window Seal Kit - Rear
Power Steering Pipe Assembly for the steering hydraulic circuit, running between the steering box and the power steering fluid reservoir. It carri...
View full detailsPower Steering Box for right-hand drive applications, supplied as a reconditioned exchange unit. The box converts steering column rotation into th...
View full detailsBush Kit Pro-Comp Only BR 2255PK
Winch Bumper - Pro Taper Large Frame is a steel front winch-mounting bumper that replaces the standard front bumper to carry a recovery winch, supp...
View full detailsSpot Light Bar mounts auxiliary driving and spot lamps across the front of the vehicle on a conventional, non-winch bumper. Formed from 2.5" diame...
View full detailsFront Differential is a complete front axle differential assembly that transmits drive from the front propshaft to the front halfshafts while allow...
View full detailsBanjo Bolt for the clutch hydraulic circuit, at the master cylinder pipe connection. This hollow bolt secures the banjo fitting of a clutch hydrau...
View full detailsLamp Guard Set - a hinged pair of protective guards that fit over the rear lamp units to shield the lenses and bodies from impact, branches and loa...
View full detailsLoading Space Mat
Rally 1000 Long Range Driving Light
Adjustable-Height Tow Bar mounting to the rear cross-member to provide the vehicle's towing attachment point. The drop-plate design allows the hit...
View full detailsTouch-Up Paint Stick in Zambesi Silver. The stick applies a small quantity of colour-matched paint to stone chips and minor scratches, restoring t...
View full detailsFan Motor Bracket that mounts and locates the cooling fan motor within the engine cooling and air conditioning installation. The bracket secures t...
View full detailsTouch-Up Paint Pencil in Bonatti Grey Metallic (paint code 19K512). The pencil applies a small quantity of colour-matched paint to stone chips and...
View full detailsFog Lamp Set is a matched pair of rectangular front fog lamps with black housings. The lamps mount above or below the front bumper to improve forw...
View full detailsSynchroniser Kit - 5th/Reverse Gear for the R380 five-speed manual gearbox, serving the mainshaft 5th gear and reverse gear assembly. The synchron...
View full detailsTow Bar Wiring Kit wires the towing electrical circuit to a 12N 7-pin single socket. It connects the vehicle road-lighting circuit through to the ...
View full detailsRear Wing - Right Hand (Offside) - outer rear quarter panel of the five-door station wagon body, part of the lower rear body structure. The wing f...
View full detailsFuse Box Housing for the main wiring harness. This housing carries the fuses that protect and distribute the vehicle's electrical circuits, provid...
View full detailsPanel bodyside
Alternator Pulley for the 2.5L 300TDi turbo diesel, part of the alternator drive in the engine's charging system. The pulley mounts on the alterna...
View full detailsStarter Solenoid for the engine cranking circuit, mounted on the starter motor body. When energised by the ignition switch it throws the starter p...
View full detailsCylinder Block Screw is a threaded fastener used on the V8 EFI petrol cylinder block assembly. It secures ancillary components and mounting bracke...
View full detailsModulator ABS Wabco SRB101550 / SRB101551 / SRB101552
Valve modulator OEM WABCO NEW (exchange)
Brush Set Startermotor
Rotor Arm for the distributor ignition system of the 3.5L V8 twin-carburettor petrol engine. Mounted on the distributor shaft beneath the cap, the...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →