for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Radius Arm locates the front axle in the suspension, controlling its fore-and-aft movement. Running between the front axle and the chassis, it res...
View full detailsPAS Pipe - Box to Reservoir is the low-pressure return pipe in the power-assisted steering hydraulic circuit, carrying fluid from the steering box ...
View full detailsFront Door Inner Panel is the inner structural skin of the left-hand front door. It forms the inner face of the door, carrying the window channel,...
View full detailsFront Seat Back Rubbing Strip is a rubber protective strip fitted to the back of the front seat. It forms part of the front seat trim, guarding th...
View full detailsFront Seat Cover is a vinyl upholstery cover for the front seat, including the head restraint section. It fits over the seat foam and frame as par...
View full detailsGear shift block
Bonnet Insulation Bracket retains the bonnet insulation pad against the underside of the bonnet panel, holding the sound-deadening and heat-insulat...
View full detailsHose Clip, a general-purpose clip for securing hose connections across the engine bay. It clamps a hose onto its pipe or stub and holds the joint ...
View full detailsGlow Plug Wiring Assembly - the glow plug (heater plug) interconnect harness within the diesel cold-start preheating circuit of the 2.5L 4-cylinder...
View full detailsChassis Wiring Harness - the main wiring loom that runs along the vehicle chassis, part of the body electrical system. It carries power and signal...
View full detailsOil Pressure Transducer measures engine oil pressure within the oil filter and pump circuit. Threaded into the oil gallery at the filter housing, ...
View full detailsDump Valve for the air cleaner housing. The flexible one-way valve fits at the lowest point of the air filter housing and lets accumulated dust and...
View full detailsPower Steering Pipe - Pump to Steering Box from the power steering hydraulic circuit, for right-hand drive applications. This high-pressure pipe c...
View full detailsUpper Steering Column from the steering wheel and column assembly. The upper column carries the steering shaft from the steering wheel boss down t...
View full detailsSteering Box is the manual steering gear that converts steering wheel rotation into the lateral movement of the steering linkage. This is the Adwe...
View full detailsFuel Filler Caution Decal for diesel-engined vehicles. This adhesive label is fitted at the fuel filler to identify the vehicle as diesel and warn...
View full detailsBrake Pipe for the hydraulic braking circuit. The rigid pipe carries pressurised brake fluid between the master cylinder, brake valve and the wheel...
View full detailsPower Steering Hose forms part of the power steering hydraulic circuit, carrying fluid from the reservoir to the steering pump. This low-pressure ...
View full detailsPanhard Rod for the front axle, part of the live-axle suspension linkage. The Panhard rod connects the axle to the chassis on one side and locates...
View full detailsCoil Spring for the road-specification suspension, supplied to heavy-duty rating. The Green/Yellow/White paint marking is the manufacturer's sprin...
View full detailsCoil Spring for the coil-sprung suspension, heavy-duty road rate. The spring mounts between the axle and the chassis, supporting the vehicle's wei...
View full detailsRadiator Upper Mounting Bracket secures the top of the radiator in the cooling system, locating it at its upper right-hand mounting point against t...
View full detailsWaterdam Panel, left-hand. The water shield fitted inside the rear side door, between the inner door skin and the trim panel. It forms a barrier a...
View full detailsWaterdam Panel, right-hand. The water shield fitted inside the rear side door, between the inner door skin and the trim panel. It forms a barrier ...
View full detailsFront Seat Pivot Bracket for the front seat mounting assembly. This bracket forms the hinge point that secures the front seat to its base while al...
View full detailsSeat Base Insulation Pad is a moulded insulation panel fitted within the front seat base assembly, sitting between the seat structure and the under...
View full detailsSeat Base Insulation Pad is a moulded insulation panel fitted within the front seat base assembly, sitting between the seat structure and the under...
View full detailsV8 Decal is a self-adhesive exterior body decal in silver, applied to the body panel as the V8 model identifier. It is fitted to restore a faded o...
View full detailsRoller bearing OEM
Carburettor Float for the SU carburettor float chamber, within the fuel metering circuit of the 3.5L V8 twin-carburettor petrol engine. The float ...
View full detailsMirror — exterior rear view mirror for the left-hand side, mounted to the door or door frame. Gives the driver a rearward view along the left flan...
View full detailsFront Door Inner Panel is the inner structural skin of the right-hand front door. It forms the inner face of the door, carrying the window channel...
View full detailsO-Ring - seals the oil pump within the engine lubrication circuit. It forms the static seal between the oil pump and its mating face, preventing p...
View full detailsFront Door Deflector deflector fitted to the right-hand front door. Directs airflow and water away from the front door opening.
Body Side Glass is a fixed glazing panel set into the body side, glazed permanently into its aperture rather than opening. It forms part of the si...
View full detailsFuse
Oil Cooler Hose - Intermediate forms the middle section of the oil cooler hose run on V8 petrol models fitted with the ZF 4-speed automatic transmi...
View full detailsDoor Lock Link operates within the rear side door latch mechanism, transferring the movement of the inner door handle to the latch to release the d...
View full detailsPlain Washer - a flat fastening washer with a sherardized (zinc-diffusion) anti-corrosion finish. Fitted under a bolt or nut to distribute clampin...
View full detailsDoor Lock Link is the connecting rod within the door latch mechanism that couples the inner door handle to the latch locking action, transferring t...
View full detailsHex Nut is an M16 hexagonal fastening nut used to secure threaded studs and bolts in body, chassis and running-gear assemblies.
Seat Mounting Bracket is the structural mounting point that locates and supports the rear forward-facing split seat, securing the seat base to the ...
View full detailsDoor Latch Link - the connecting rod that transfers movement from the sill locking button and exterior handle to the front door latch. It links the...
View full detailsWindow Draught Spacer - a packing spacer fitted behind the side window draught rail. It sets the rail at the correct stand-off from the glass so th...
View full detailsCrankshaft Position Sensor for the V8 EFI petrol engines, part of the engine management system. The sensor reads a toothed reluctor driven by the ...
View full detailsSeat Cover - a waterproof cover for the rear seat, fitted over the seat to protect the upholstery from water, mud and general wear.
Power Steering Pipe connecting the steering box to the fluid reservoir within the power steering hydraulic circuit. This pipe routes return-side p...
View full detailsTiming Bolt, M10 x 20 - socket head fixing from the timing drive assembly. On belt-driven diesel applications the bolt secures the timing belt ten...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →