for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Door Card - interior trim panel for the front door, right-hand (RH). It covers the inner face of the door, providing a finished surface over the do...
View full detailsRear Quarter Glass - fixed glazing panel for the rear body side, formed from 5mm tinted toughened automotive safety glass. It glazes into the rear...
View full detailsHeater Air Duct - fan cowl section of the heater air intake. This duct forms the fan cowl part of the heater intake, channelling air into the heat...
View full detailsFront Valance Panel lower front body panel for the left-hand side, part of the front bodywork. Closes the lower front section of the body below th...
View full detailsPower Steering Box is the recirculating-ball steering gear that converts rotation of the steering wheel into the side-to-side movement of the drop ...
View full detailsPower Steering Box is the recirculating-ball steering gear that converts rotation of the steering wheel into the side-to-side movement of the drop ...
View full detailsFacia Vent Finisher - the trim surround that frames an air outlet on the dashboard facia. This finisher is for vehicles fitted with air conditioni...
View full detailsWindscreen Demist Vent Finisher - the trim that caps the demister outlet at the top of the facia, where the screen demist vent meets the base of th...
View full detailsFuel Filter Bracket mounts and supports the fuel filter assembly within the diesel fuel supply system. It secures the filter housing to the surrou...
View full detailsRadiator Bracket - LH is the left-hand mounting bracket that locates and secures the radiator within the engine cooling system. It holds the left-...
View full detailsRear Brake Disc - Wavy, Cross-Drilled & Grooved for the rear axle disc-brake assembly. The disc mounts to the rear hub and provides the frictio...
View full detailsTruck Cab Bracket is a mounting bracket for the truck cab body. It secures the truck cab section to the vehicle. Fitted two per vehicle.
Rear Brake Disc - Pair for the rear axle disc-brake assembly, supplied as a matched set for both rear wheels. Each disc mounts to the rear hub and ...
View full detailsRear Lamp Cover Panel – LH is a body panel fitted at the left-hand rear of the vehicle, forming the mounting surround that locates and frames the r...
View full detailsWiper Mechanism Nut Plate for the windscreen wiper assembly. It provides the threaded mounting points that secure the wiper mechanism to the body,...
View full detailsCylinder Head Gasket for the 300TDi 2.5L four-cylinder turbo diesel engine, sealing the joint between the cylinder head and the engine block. It s...
View full detailsHeadlamp for the front exterior lighting assembly, supplied as a complete halogen unit. The headlamp provides manual beam levelling, allowing the ...
View full detailsGear Lever Assembly for the R380 five-speed manual gearbox. The lever locates in the gear change remote housing on top of the transmission and pro...
View full detailsHeater Blower Motor is the electric fan motor of the cabin heater assembly. It draws air through the heater housing and forces it across the heater...
View full detailsGear Lever Assembly for the R380 five-speed manual gearbox. The lever locates in the gear change remote housing on top of the transmission and pro...
View full detailsStainless Steel Wing Top Vent A perforated stainless steel vent for the wing-top air intake aperture, left-hand side. The drilled vent face admits...
View full detailsStarter Motor Drive for the Bosch-type starter motor fitted to the 3.5L V8 petrol engine. The drive carries the pinion and a one-way (overrunning)...
View full detailsWaterproofing Kit - V8 seals the ignition system of the V8 petrol engine against water and damp. The kit waterproofs the distributor and ignition ...
View full detailsDim-Dip Control Unit governs the dim-dip headlamp function within the exterior lighting circuit. The dim-dip system runs the headlamps at a reduce...
View full detailsStainless Steel Wing Top Vent A louvred stainless steel vent for the wing-top air intake aperture, right-hand side. The angled louvres admit air i...
View full detailsSealed Beam Headlamp Unit for the front lighting system, supplied to the left-hand-drive (LHD) dip pattern. A sealed beam unit combines the lens, ...
View full detailsRelay rated at 12V, 40A in a 5-pin changeover configuration, used at various positions in the vehicle's electrical system. A changeover relay uses...
View full detailsOuter Body Panel - LH - a left-hand outer body panel, forming part of the external bodywork on the left-hand side of the vehicle.
Switch-h/Lamp-l
Stainless Steel Wing Top Vent A louvred stainless steel vent for the wing-top air intake aperture, left-hand side. The angled louvres admit air in...
View full detailsStainless Steel Side Vent A perforated stainless steel side vent grille for the front wing, left-hand side. The drilled vent face allows air to pa...
View full detailsOil Pump Repair Kit for the oil pump of the 3.5L V8 petrol engine. The kit reconditions the engine oil pump and its pressure-relief valve, restori...
View full detailsRear Trailing Link Bracket forms part of the rear suspension's axle-location assembly. It provides the chassis-side mounting point for the rear tr...
View full detailsStainless Steel Side Intake A stainless steel air intake grille for the front wing, left-hand side, covering the wing-top intake aperture that admi...
View full detailsStainless Steel Wing Top Vent A perforated stainless steel vent for the wing-top air intake aperture, right-hand side. The drilled vent face admit...
View full detailsDistributor Pick-Up Plate for the electronic ignition distributor on the 3.5L V8 petrol engine. The plate is the base assembly inside the distribu...
View full detailsClutch Pedal Assembly is the foot-operated pedal and mounting bracket in the clutch control system. Pivoting on its bracket in the footwell, it tra...
View full detailsBolt
Crankshaft Damper Remover is a workshop special tool used to draw the crankshaft vibration damper (torsional damper pulley) off the crankshaft nose...
View full detailsFuel Filler Cap for the fuel tank, finished in grey. The cap closes and seals the fuel tank filler neck, retaining fuel vapour and keeping dirt an...
View full detailsInhibitor Switch mounts on the ZF automatic transmission. It prevents the engine from cranking unless the selector is in Park or Neutral, and sign...
View full detailsStarter Motor Brush Kit
Screw, M12 x 20 hexagonal-head set screw, a general-purpose threaded fastener used across several chassis and drivetrain mounting points. Typical ...
View full detailsMain Bearing Set for the crankshaft main journals, in 0.030-inch oversize. The set supplies the main bearing shells that carry the crankshaft in t...
View full detailsDistributor Pump Timing Tool is a workshop special tool used to set the injection timing of the rotary (distributor-type) diesel injection pump on ...
View full detailsTransfer Box Differential Gear Kit for the centre differential of the LT230 transfer box. The kit renews the centre differential gear set, which s...
View full detailsInner Wing - left-hand inner wing panel. The inner wing forms the structural side of the engine bay and front wheel arch, supporting the outer wing...
View full detailsPedal Pad – a moulded rubber cover that fits over a foot pedal to give the driver a durable, non-slip contact surface. The pad locates over the pe...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →