for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Seat Belt - front occupant restraint for the right-hand seating position. Supplied with red webbing to suit the Truck Cab body and mounting to the...
View full detailsFlywheel and clutch kit for the Td5 clutch assembly, supplied as a matched set. The flywheel bolts to the rear of the crankshaft and provides the ...
View full detailsSeat Belt - front occupant restraint for the left-hand seating position. Supplied with red webbing to suit the Truck Cab body and mounting to the ...
View full detailsBonnet sound deadening pad, forming part of the engine bay acoustic insulation. Fitted to the underside of the bonnet panel directly above the eng...
View full detailsWire Harness 13PIN - Defender 90 1
Cylinder Head Bolt Kit - a set of cylinder head bolts for the 2.5L 200 TDi turbo diesel engine. The bolts clamp the cylinder head to the block acr...
View full detailsSound Deadening panels cut for the front footwells, applied directly to the bare floor panel beneath the carpet or mat. The material is a self-adh...
View full detailsFlanged Head Screw used in the door latch mechanism and the tailgate lock control assembly. The integral flange spreads clamping load, removing th...
View full detailsHeated Mirror Kit - an upgrade that adds heating to the exterior wing mirrors, retro-fitting to the existing mirror glass. The kit supplies a pair...
View full detailsSports Exhaust System - full stainless steel exhaust system for the 3.5 V8 petrol engine, supplied complete from the cylinder head flanges back to ...
View full detailsSeat Belt - front occupant restraint for the right-hand seating position. Supplied with red webbing to suit the Station Wagon body and mounting to...
View full detailsTiming Belt Kit - 300TDi - the timing drive components housed behind the front timing cover of the 300Tdi 2.5L four-cylinder turbo diesel engine. ...
View full detailsAir locker - a pneumatically operated differential lock that replaces the standard differential centre in a Rover-type axle running 24-spline halfs...
View full detailsCoolant header tank in aluminium, forming the expansion and filling point of the engine cooling circuit. The tank absorbs the change in coolant vo...
View full detailsWaterproof Seat Covers - supplied as a pair, cut to fit the Defender front seats. Made from polyester with an EVA waterproof layer, the covers fit...
View full detailsSound deadening panel for the rear wheel arches, forming part of the interior acoustic insulation. Applied to the inner face of the wheel arch, wh...
View full detailsFront Wheel Bearing Kit containing the parts needed to overhaul one front hub bearing assembly. The taper roller bearings carry the front hub on th...
View full detailsSeat Recliner Handle and Cover Kit for the front seat frames. The recliner handle operates the backrest adjustment mechanism on the outboard side ...
View full detailsAir Conditioning Evaporator Core - the heat exchanger inside the heater and air conditioning housing in which the refrigerant evaporates, cooling a...
View full detailsSnorkel - raised air intake assembly that relocates the engine air intake from the wing top to roof level. The body mounts to the front wing and r...
View full detailsTransfer Box Overhaul Kit for the LT230 transfer box. The LT230 is the two-speed transfer box that splits drive from the gearbox between the front...
View full detailsFront Suspension Bush Kit for the radius arms and Panhard rod. Contains the rubber bushes to replace those at both ends of the front radius arms a...
View full detailsRadius Arm Bush Kit renews the bush at the chassis end of the front radius arm, where the radius arm mounts to the chassis. The bush locates the f...
View full detailsFulcrum Bracket - High Articulation forms the apex mounting of the rear A-frame - the triangulated top link that locates the rear axle and controls...
View full detailsService Kit Inc Cataclean - Defender & Discovery 2 TD5
Timing Chain Kit for the 2.5L Td5 five-cylinder turbo diesel engine. The timing drive sits at the front of the engine behind the timing cover and ...
View full detailsPiston Ring Set for the 3.9 litre Rover V8, supplied at standard size and covering one piston - eight sets are required to do a complete engine. T...
View full detailsW/Proof Seat Covers Rear 60/40 - Defender 110 to 07
Fuel Filler Surround
Acoustic Mat is a moulded sound-deadening cover for the seat box, the central housing that encloses the gearbox and transfer box between the front ...
View full detailsFront Suspension Bush Kit for the radius arms and Panhard rod. Contains the rubber bushes to replace those at both ends of the front radius arms a...
View full detailsHinge Guard - 2 Door is a door security set fitted at the hinge-to-bulkhead joint of the front doors. Each guard is made up of two precision-cut 2...
View full detailsFuel Pick-Up and Return Pipe Assembly for the fuel tank on diesel applications using the metal fuel tank. The pick-up pipe draws fuel from inside ...
View full detailsSteering Guard - a heavy-gauge steel skid plate that bolts beneath the front of the chassis to shield the steering linkage and steering damper from...
View full detailsLT77 Five-Speed Manual Gearbox, build specification 54A, supplied as a reconditioned unit. The LT77 is a five-speed all-synchromesh manual gearbox...
View full detailsCamshaft Bolt for the 2.5L 300 Tdi diesel engine. Retains the camshaft drive gear on the camshaft within the timing drive.
Rear Brake Discs - supplied as a pair for the rear axle. Solid (non-vented) brake discs providing the friction surface that the rear brake pads cl...
View full detailsAir Conditioning Compressor for the R134a air-conditioning system. Belt-driven from the engine, it pressurises and circulates refrigerant around th...
View full detailsBumper Tread Plate - a pair of protective tread plates for the bumper. Fitted over the bumper top surface, they guard the paintwork against scuffi...
View full detailsBrake Pipe Connector - a junction fitting in the hydraulic brake circuit that joins rigid brake pipes. It provides a sealed connection between bra...
View full detailsBolt for towing equipment fixings. Hexagon-head threaded fastener used to secure the towing drop plate and tow ball assembly, including High Capac...
View full detailsBlind Nutsert is an M6 blind rivet nut (rivnut) that provides a captive threaded fixing point. It is set into a single face of sheet metal or pane...
View full detailsTow Hook Cover is a protective cover for the 50mm tow hook. It fits over the towing hook to protect it when not in use and to give a finished appe...
View full detailsHydraulic Jack & Handle - the vehicle-supplied lifting equipment carried in the on-board tool kit for wheel changes and roadside servicing. Th...
View full detailsRubber Mount is an axle assembly mounting bush. It isolates the axle-mounted assembly from the surrounding structure, absorbing vibration and cush...
View full detailsStabiliser Bar Link Bush is fitted at the anti-roll bar link within the suspension. It cushions the connection between the stabiliser (anti-roll) ...
View full detailsRear Indicator Lamp is a 95mm round LED lamp forming part of the rear exterior lighting cluster. It provides the rear direction-indicator function...
View full detailsHeadlamp Assembly for the front lighting system, halogen type without headlamp levelling. The complete unit houses the main and dipped beam reflec...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →