for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Wheel Arch Moulding – Rear An eyebrow trim moulding fitted to the rear wheel arch lip. It follows the curve of the wheel arch flange, covering the...
View full detailsSide Trim Panel is an interior body trim panel that lines and finishes the right-hand side of the 90" wheelbase bodyshell. It conceals the inner bo...
View full detailsHalogen Headlamp Assembly for left-hand-drive (LHD) applications. The complete front headlamp unit uses a quartz-halogen light source and is of th...
View full detailsRear Shock Absorber for the rear axle suspension, damping spring oscillation on compression and rebound to control body movement and keep the wheel...
View full detailsRear Shock Absorber for the rear axle suspension, damping spring oscillation on compression and rebound to control body movement and keep the wheel...
View full detailsFront Shock Absorber for the front axle suspension, damping spring oscillation on compression and rebound to control body movement and keep the whe...
View full detailsPlain Washer - flat unthreaded washer used within the differential assembly. It seats in the differential case at the crownwheel and pinion, provi...
View full detailsRocker Shaft Spring for the Rover V8 valvetrain, fitted on the rocker shaft assembly. The spring acts as a spacer between adjacent rocker arms, ho...
View full detailsFront Shock Absorber for the front axle suspension, damping spring oscillation on compression and rebound to control body movement and keep the whe...
View full detailsAbsorber Shock
Locker Door Hinge
Door Hinge Bolt
Tow Ball & Pin is a towing coupling component that mounts to the tow bracket or drop plate. The ball provides the coupling point onto which a ...
View full detailsBonnet Clip is a retaining clip in the bonnet latch and release assembly. It holds the bonnet release spring and catch components in position, kee...
View full detailsWide Angle Rear Propshaft for the rear driveline, connecting the transfer box output to the rear differential. It replaces the standard rear prope...
View full detailsCylinder Head Gasket seals the joint between the cylinder head and the engine block. It seals combustion pressure, coolant and oil passages across...
View full detailsSound Deadening panels cut for the seat box, applied to the seat box surfaces beneath the seats and trim. The seat box sits directly over the gear...
View full detailsRear Wheel Cylinder for the rear drum brake assembly, left-hand side. Mounted to the brake backplate, the wheel cylinder converts hydraulic pressu...
View full detailsWater Pump Seal: sealing ring for the coolant pump (Land Rover description 'Seal-coolant pump'). Used in the Td5 coolant pump installation, also i...
View full detailsGirling Shock Absorber for the front suspension, a hydraulic damper for heavy-duty suspension applications. Mounted between the axle and the chass...
View full detailsCam Cover Gasket for the 2.4L Duratorq TDCi (Puma) diesel engine, sealing the camshaft cover to the cylinder head. It forms the oil-tight joint be...
View full detailsDriving Member Nut for the front hub driving member (drive flange). This is the retaining nut that secures the driving member against the hub face...
View full detailsGrapa
Glow Plug
Front Door is a complete steel front door assembly for the left-hand (LH) side. Built around a pressed-steel frame and outer skin, it is configure...
View full detailsCamshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...
View full detailsDoor - Rear
Front Smoked Indicator LED 12V
CV Joint - front axle constant velocity joint located in the swivel housing at the outer end of the front halfshaft. It transmits drive to the fron...
View full detailsIntake Hose - an air intake hose in the engine induction system of the turbo diesel engine. It carries filtered intake air from the air cleaner as...
View full detailsLock Set is a replacement lock barrel supplied with matching keys, for the anti-burst lock system. The barrel fits into the lock housing and is op...
View full detailsHeater Plug
Sensor - Engine Temperature
Starter Motor
Caliper - Piston
Stud
Brake Pipe Assembly for the left-hand side of the hydraulic brake circuit. This rigid, pre-formed pipe carries pressurised brake fluid between the ...
View full detailsExhaust Manifold Stud secures the exhaust manifold to the cylinder head, part of the exhaust manifold mounting hardware. This is an M10 stud, thre...
View full detailsPower Steering Pump - belt-driven hydraulic pump forming the pressure source of the power assisted steering circuit. Mounted on the engine and dri...
View full detailsCoolant Temperature Transmitter - Black mounted at the thermostat housing, supplying the coolant temperature signal to the instrument cluster tempe...
View full detailsDecoke Gasket Set for the 3.9/4.0/4.2L Rover V8 EFI petrol engine. This is the set of gaskets and seals used to reseal the top end of the engine - ...
View full detailsHead Gasket
Air Intake Hose for the 2.25 litre diesel engine, forming part of the air induction system between the air cleaner and the intake manifold. It car...
View full detailsDriving Member (axle drive flange) for the front and rear hub assemblies. It bolts to the outer face of the hub and engages the splined end of the ...
View full detailsHorn - High Note
Front Axle Drive Shaft transmits drive from the front differential to the right-hand wheel hub, forming part of the front axle drive shaft and hub ...
View full detailsSill Protector Pair - exterior body protection panels that fit along the lower sill (rocker) sections beneath the doors, formed from 2mm aluminium....
View full detailsBelt
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →