for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...
View full detailsInlet Valve operates in the cylinder head valvetrain of the 2.5L 300TDi turbo diesel engine. It seals against the inlet valve seat and opens to ad...
View full detailsBulb, 12V 4W (type 233, BA9s single-contact bayonet cap), supplied as a twin blister pack of two bulbs. A miniature bayonet bulb used in number pla...
View full detailsGlow Plug for the diesel cold-start pre-heating system, threaded into the cylinder head to project into the combustion chamber (or pre-combustion c...
View full detailsCamshaft operates the valvetrain of the 2.5L 300TDi diesel engine. Its lobes actuate the pushrods to open and close the inlet and exhaust valves.
Drive Screw - a No. 6 x 5/8" self-tapping drive screw used as a body fixing. It retains the grille assembly and secures the rear door and tailgate...
View full detailsClutch Cover is the pressure plate assembly for the Td5 clutch. Bolted to the flywheel, its diaphragm spring clamps the driven plate against the f...
View full details8 Driving Lamps In Black
Drive Belt Air conditioning compressor drive belt for the 200TDi turbo diesel engine, poly-vee (multi-rib) construction. Drives the A/C compressor...
View full detailsABS Sensor - Front for Defenders with the 4 wheel anti-lock braking system. This wheel speed sensor mounts at the front axle hub and continuously ...
View full detailsFloor Panel Screw - Pack of 100
Seat Heater Kit (Retrofit, Pair) adds heating to two seats by fitting flexible heating elements between the seat upholstery and the seat cover, acr...
View full detailsCylinder Head for the 300 TDi 2.5L four-cylinder turbo diesel engine, supplied as a bare casting without valves. The head bolts to the top face of...
View full detailsPinion Seal - Salisbury Axle seals the nose of the pinion shaft at the front of the Salisbury differential housing, where the propshaft coupling fl...
View full detailsFront Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...
View full detailsGasket - Exhaust Manifold
Brake Pipe Assembly for the right-hand side of the hydraulic brake circuit. This rigid, pre-formed pipe carries pressurised brake fluid between the...
View full detailsHose - Oil
Heater Deflector fits to the outer heater housing to redirect heated air from the outlet into the footwell. Part of the HVAC heater assembly, it c...
View full detailsCamshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...
View full detailsConnecting Rod Bearing Set for the 2.5L 4-cylinder engine, supplied in 0.030" oversize. These are the big-end shell bearings that fit between the ...
View full detailsCrankshaft Spigot Bearing - 2.4 TDCi
Oil Filler Cap closing the engine oil filler neck on the rocker cover. It seals the filler aperture to keep the lubrication system closed and prev...
View full detailsRear Indicator Lamp for the exterior lighting system, fitted within the rear lamp cluster. This is the smoked-lens LED version, operating at 12V: ...
View full detailsWindscreen Brackets - a pair of CNC-machined billet aluminium brackets with a silver anodised finish that secure the windscreen frame at its lower ...
View full detailsCoupling - Viscous Borgwarner
Taper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...
View full detailsFront Cover Gasket for the 2.4L Duratorq TDCi (Puma) diesel engine, also used on the 2.2L Puma TDCi. It seals the joint between the engine front (t...
View full detailsFuel Stop Solenoid for the 200 Tdi and 300 Tdi 2.5L turbo diesel engine, mounted on the fuel injection pump. Held open while energised through the...
View full detailsInhibitor Switch
Exhaust Manifold Gasket for the 200 TDi diesel engine, sealing the joint between the exhaust manifold and the cylinder head. It seals each exhaust...
View full detailsRear Door Glass - the glass assembly for the rear end (tail) door. It incorporates a heated element for demisting the rear window and an integrate...
View full detailsLayshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...
View full detailsIntercooler for the turbocharger charge-air circuit on Td5 and Puma TDCi diesel engines. Mounted in the airflow ahead of the radiator, the interco...
View full detailsRear Brake Caliper Piston for the rear disc brake caliper. The piston runs in the caliper bore behind the square-section piston seal and dust boot,...
View full detailsFront Right-Hand Brake Pipe for the hydraulic braking circuit, non-ABS systems. This pre-formed rigid steel pipe carries brake fluid through the f...
View full detailsPiston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...
View full detailsConnecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...
View full detailsRaised Air Intake Fitting Kit - fitting hardware for the Terrafirma raised air intake, supplied separately from the intake itself. The raised air ...
View full detailsFitting Kit for Pacet Fan
Rear Stub Axle for the Salisbury rear axle assembly. The stub axle bolts to the outer end of the axle casing and forms the fixed spindle on which ...
View full detailsRear Light Lens for the rear stop and tail lamp. The red lens fits over the lamp body to cover the stop and tail bulb, transmitting the brake ligh...
View full detailsAlternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...
View full detailsExhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...
View full detailsHeater Blower Duct Seal for diesel applications, fitted in the heater air intake. This foam seal sits between the air inlet duct and the heater blo...
View full detailsABS Wheel Speed Sensor - front sensor for the four-wheel anti-lock braking system. The sensor mounts in the front axle housing with its pole piece...
View full detailsRetaining Clip for the output shaft oil seal on the MT82 6-speed manual gearbox. The clip locates and secures the oil seal within the gearbox hous...
View full detailsMain Bearing Set 020 (Lc)
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →