for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Shift Plate
Rear Spring Dislocation Cone - seats into the base of the rear coil spring mount and allows the spring to unseat (dislocate) cleanly at full axle d...
View full detailsFour-Stage Adjustable Shock Absorber for the suspension damping circuit, mounted between the axle and the chassis mounting point. The damper contr...
View full detailsFlange Bolt Hex-head flange bolt, M8 x 1.25 x 80mm. General-purpose fastener used in chassis frame and component mountings.
Wheel Arch Kit: a complete set of standard width wheel arches with a gloss black finish. The semi-flexible, vacuum-formed plastic arches replace t...
View full detailsOil Seal
Window Channel Shim - 3mm for the front door glass channel. This 3 mm shim sets the packing thickness behind the front door window channel (glass ...
View full detailsConnecting Rod Bolt for the Rover 3.5L V8 petrol engine. The bolt clamps the connecting rod big-end cap to the rod, retaining the big-end bearing s...
View full detailsFacia Ashtray is a moulded ashtray assembly that seats in the upper crash pad section of the facia. It locates in the dedicated aperture in the da...
View full detailsSoft Top Drain Channel runs along the left-hand side of the soft top, directing rainwater run-off from the canopy away from the body sides.
Fuel Injector - fuel injection system, cylinder head. Td5 2.5L 5-cylinder turbo diesel. The Td5 uses electronic unit injectors: each injector sits...
View full detailsRear Propshaft transmits drive from the transfer box output to the rear axle differential, forming part of the vehicle driveline. It carries a uni...
View full detailsRear Wing - nearside (left-hand) rear bodyside outer panel. Part of the exterior body structure, forming the outer skin of the rear body side above...
View full detailsAir Conditioning Retrofit Kit - a complete air conditioning installation for the Td5 2.5L 5-cylinder turbo diesel, in left-hand drive configuration...
View full detailsbush shock absorber OEM, bush anti roll bar OEM
Door Lock Striker Seal for the left-hand front door, fitted behind the striker at the door latch mechanism. It seals the striker mounting to the b...
View full detailsThe Maxtrac Blindo 16x7 alloy wheel is designed for off-road durability and rugged performance, making it the perfect choice for Land Rover and 4x4...
View full detailsTubular Winch Bumper - Without A-Bar, Without Air Conditioning - one-piece tubular front bumper with integral winch mounting, for vehicles built wi...
View full detailsTerrafirma Tubular black powder coated, high approach angle off road winch bumper with built in A Bar as well as jacking and recovery points for De...
View full detailsRubber Headlamp Bulb Cover for the rear of the headlamp unit. This rubber cover seals the bulb access aperture at the back of the headlamp housing...
View full detailsUniversal Joint is the cross-and-bearing (Hardy Spicer) joint used in the propeller shaft. It allows the propshaft to transmit drive through an an...
View full detailsKit rear caliper pistons and seals OEM AP 110/130 upto (VIN) 1A614447 1 kit per caliper.
Conrod bearing set .030"" KING
Mass Air Flow Sensor - TDCi is the intake air mass sensor for the TDCi diesel engine, forming part of the air intake assembly. Fitted in the intak...
View full detailsSwivel Housing Kit for the front axle swivel assembly, for vehicles fitted with ABS. The kit covers one side of the axle. It rebuilds the swivel j...
View full detailsShock Absorber - a gas-charged front damper for the suspension. Fitted between the front axle and the chassis, it damps the motion of the road spr...
View full detailsRear Side Door Glass - fixed glazing panel for the rear side door, formed from 5mm clear (untinted) toughened automotive safety glass. It sits wit...
View full detailsRear Gas Shock Absorber - a gas-charged hydraulic damper for the rear suspension, controlling axle movement over road and off-road terrain. Matche...
View full detailsFuel Pipe Assembly - part of the fuel delivery circuit for the carburettor V8. It carries fuel from the fuel supply line to the SU carburettors, fe...
View full detailsR-Clip - spring steel retaining clip for the centre pin of the military (NATO) pattern front bumper, part of the front bumper and towing pin fixing...
View full detailsDust Cover for the A-frame ball joint in the rear suspension top link and fulcrum assembly. The cover fits over the ball joint to keep grease in a...
View full detailsSide Lamp Lens, the late 'fish-eye' front type for military-specification side lamps. The lens fits the front side lamp body to seal the bulb apert...
View full detailsDoor Lock Link is the connecting rod within the front door latch mechanism that couples the inner door handle to the latch locking action, transfer...
View full detailsFront Housing Gasket for the LT95 four-speed gearbox fitted to V8 engines. It seals the joint between the gearbox front housing and the main casin...
View full detailsHand Throttle Cable is the secondary throttle control cable, operated by a hand control rather than the accelerator pedal. It holds the throttle l...
View full detailsbracket exhaust OEM - 90" 4-cyl N/A diesel and 90" 4-cyl petrol (except MPI)
Double Cardan Front Propshaft for the front drivetrain circuit on Defender Puma models with the 2.4L and 2.2L TDCi engines. 680 mm shaft length. T...
View full detailsSeat Belt - Rear - Forward Facing - Static is part of the rear occupant restraint system. This is a static (non-retracting) belt that secures an o...
View full detailsRear Door Trim Panel - Dark Granite for the Defender interior door trim assembly. This panel fits the rear door (tailgate) on Defender models equi...
View full detailsA/C Suction Pipe - low-pressure suction line of the air conditioning refrigerant circuit. It carries low-pressure refrigerant vapour from the evap...
View full detailsWater Pump Pulley for the 2.5L 300 TDi turbocharged diesel engine, mounting to the water pump hub within the engine cooling circuit. The pulley is...
View full detailsEGR Cooler Gasket - seals the exhaust gas recirculation (EGR) cooler to its mating flange in the EGR circuit, preventing leakage of recirculated ex...
View full detailsAlloy Wheel, 16 x 7 inch, finished in gloss black. The wheel has a positive offset of ET+11 (11 mm) and a rated load capacity of 1,400 kg per whee...
View full detailsScrew securing the front catch of the rear side sliding window. Used to fix the sliding window catch on Station Wagon bodies of early Series models.
Injector Dowel Ring for the fuel injection system of the 2.5L 200 TDi engine. This locating dowel positions the injector correctly in the cylinder...
View full detailsRetaining Lock Clip that secures the operating link to the door latch mechanism. The clip holds the latch linkage rod in position, maintaining the...
View full detailsBrake Pipe Assembly – Primary is a pre-formed rigid pipe in the hydraulic braking circuit. The primary pipe carries hydraulic pressure from the ma...
View full detailsBrake Pipe Assembly is a pre-formed rigid pipe in the hydraulic braking circuit. It carries hydraulic pressure between the brake circuit component...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →