for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Parts Catalogue - illustrated parts reference. This catalogue lists the original equipment part numbers alongside exploded assembly diagrams, allo...
View full detailsBolt used in multiple assembly applications including towing equipment, engine mounting, front stabilizer bar, ACE system, and seat belt anchorage.
Camshaft Pulley for the 2.5L 4-cylinder naturally aspirated diesel and 2.5L turbo diesel engines. Located at the front of the cylinder head, the c...
View full detailsPivot Lever Pin is the selector pivot pin in the LT230 transfer box, providing the pivot point about which the range selector lever swings. It loc...
View full detailsPiston Ring Set in standard size, for the 2.25L and 2.5L naturally aspirated four-cylinder diesel engines running standard-size pistons in an unbor...
View full detailsOil Pump Bolt for the Rover 3.5L V8 petrol engine, 1/4" UNC x 1 1/4". The bolt secures the oil pump to the timing cover, retaining the pump body th...
View full detailsBearing layshaft LT95 4-speed manual gearbox for Rover 3.5L V8 - S3 109" Stage One V8 - early 110" V8 (Stage Two) - 101" Forward Control - Classic...
View full detailsSeat belt assembly individual rear LH 110" 4 Door Crew Cab - Non HICAP
Transfer Box - LT230 43D is a reconditioned two-speed transfer gearbox with a 1.4:1 high-range ratio. The transfer box mounts to the rear of the m...
View full detailsRear Step Bumpers - a pair of skeleton-style rear corner bumperettes that bolt to the rear cross member. Each corner is built from mandrel-formed ...
View full detailsHeater Control Assembly for right-hand-drive applications, mounting in the dashboard heater control panel to regulate cabin heating and ventilation...
View full detailsDoor strengthening brackets for the rear door, reinforcing the door frame where a rear-mounted spare wheel carrier is bolted on. The brackets stif...
View full detailsAnti-Roll Bar Bush locates the anti-roll bar at its mounting to the chassis, holding the bar in position while allowing it to rotate as the suspens...
View full detailsLayshaft Bearing for the front of the LT77 five-speed manual gearbox layshaft. The bearing supports the forward end of the layshaft (countershaft)...
View full detailsMainshaft Bearing for the LT77 five-speed manual gearbox. This tapered roller bearing supports the gearbox mainshaft, locating it within the gearb...
View full detailsPolyurethane Suspension Bush Kit - Classic Red grade. This kit replaces the original rubber suspension bushes with polyurethane items in the Polyb...
View full detailsTrack Rod Protection Bracket from the front axle assembly. It mounts to the front differential housing and shields the steering track rod. The bra...
View full detailsExhaust U-Bolt secures the exhaust system at its mounting points, clamping the pipe to a bracket or holding adjacent sections of the exhaust line t...
View full detailsSnow Cowl for the wing-top heater air intake, fitting in place of the standard intake grille on the left-hand wing of right-hand-drive vehicles. T...
View full detailsRadiator Grille - Santorini Black - Front for the front body panel and front-end cooling assembly. The grille sits in the front panel ahead of the ...
View full detailsSeat Re-Trim Kit supplies the materials to re-cover and re-pad the front centre seat, restoring a worn or damaged seat to a finished trim. The kit...
View full detailsRear Dislocation Cone is a suspension component for the rear coil springs, fitted at the spring seat to guide a spring that unseats at full droop b...
View full detailsFloor Mat - moulded rubber floor mat for the front right-hand footwell, part of the interior floor protection and trim group. Shaped to the footwe...
View full detailsGearbox Extension Case Screw for the R380 5-speed manual gearbox. M5 × 30 Torx head screw used to secure the extension case on the R380 gearbox. T...
View full detailsSeat Squab Cover for the front seat backrest (squab), forming the outer covering over the backrest cushion. It replaces a worn, torn or faded origi...
View full detailsTwo-Man Bench Seat Cushion for the rear inward-facing bench seat. This is the fixed rear bench cushion that forms the seating surface of the two-s...
View full detailsRear Lamp Base - the mounting base for a rear lamp unit. The common base used across the rear indicator, fog and reverse lamp positions, so more t...
View full detailsThrust Washer is a 1.05mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...
View full detailsHeater Resistor Pack - the blower-speed control resistor in the heating and ventilation (HVAC) system. It sits in the heater blower circuit betwee...
View full detailsFront Wheel Bearing Kit supplying the parts needed to overhaul the wheel bearings on a single front hub. The components fit the stub axle and hub ...
View full detailsThrust Washer for the differential pinion of the Salisbury rear axle. The washer sits behind a differential pinion gear, setting its running cleara...
View full detailsFuel Pipe Olive is a compression ferrule used to seal a rigid fuel pipe union. The olive is compressed onto the pipe by the union nut to form a le...
View full detailsA/C O-Ring - a sealing O-ring for the manual air conditioning system. It seals a refrigerant pipe or hose coupling in the air conditioning circuit...
View full detailsStripped Engine is a base engine assembly for the 2.4L Td4 (TDCi Puma) diesel, supplied as a ready-to-build unit onto which the ancillaries from th...
View full detailsSelector Cover Gasket - LT95
Drain Plug - a threaded plug that seals a drain point and is removed to drain fluid during service. It is used in several locations depending on ap...
View full detailsOil Pump Gasket for the LT95 four-speed gearbox. It seals the oil pump to the gearbox casing on the LT95 transmission, used behind the Rover V8 an...
View full detailsPiston Ring (+.020" Oversize) for the 2.5L 200 TDi four-cylinder turbo diesel engine, forming part of the piston, connecting rod and bearing assemb...
View full detailsSpring Pin for the soft-top drain channel assembly. The slotted, sprung-steel pin is driven through aligned bores to retain a component on its shaf...
View full detailsClutch Cover Bolt secures the clutch cover (pressure plate) to the flywheel within the clutch assembly. Threaded M8 x 13mm, fitted on the 6-speed ...
View full detailsCarburettor Insulator - 2-Barrel is the heat-isolating spacer block fitted between the 2-barrel carburettor and the inlet manifold. The insulator ...
View full detailsTorx Pan Head Bolt, M8 x 50. A pan head bolt with a Torx drive recess, used as a body and hinge fixing - including the cable-operated bonnet assem...
View full detailsLocking Nut, a self-locking fixing used across body trim, door casings and bumper fixings. The locking feature resists loosening under vibration.
Con Rod Bearing Set - a set of connecting-rod (big-end) bearing shells for the 2.2L TD4 diesel engine, supplied in standard size. The shells sit b...
View full detailsEngine Gasket Set for the 2.4 TDCi (Td4) diesel engine. A complete engine gasket set covering the lower engine assembly. The cylinder head gasket ...
View full detailsEnsure optimal engine performance and reliability in your Land Rover Defender 2.4L & 2.2L Puma (2007-2016) with this complete timing chain kit....
View full detailsEnhance the comfort and quality of your Defender 90/110 with Dynamat Xtreme Sound Deadening for the bonnet. Specially designed for Defender models ...
View full detailsUpgrade your vehicle's lighting with these 8-inch black halogen driving lights. High power 100W lamps with universal fitting, plastic stone guards,...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →