for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Oil Pressure Switch - threaded into the oil filter/cooler housing on the engine lubrication circuit, it senses engine oil pressure. It signals the...
View full detailsAir Intake Grille for the heater fresh-air intake, mounted on the left-hand (near-side) wing top above the bulkhead. The grille covers the air duc...
View full detailsOil Dipstick for the 2.4L Duratorq-TDCi (Puma) diesel engine. It locates in the dipstick tube to allow the engine oil level in the sump to be check...
View full detailsSpare Wheel Carrier Spacer for the rear-door mounted spare wheel carrier. It spaces the spare wheel carrier stud mounting on the rear door, settin...
View full detailsConstant-Velocity (CV) Joint for the front axle drive, non-ABS applications. Heavy-duty specification. The CV joint sits at the outer end of the f...
View full detailsCV & Stub Shaft Assembly for the front axle drive, combining the constant-velocity joint with its stub shaft. It transmits drive from the halfs...
View full detailsSteel Snorkel Kit (raised air intake) from the Mantec range, forming part of the engine air intake system. Relocates the air intake from the stand...
View full detailsClutch plate 130 OEM VALEO
Fitment: V8 from Vin 252258
Layshaft for the LT77 five-speed manual gearbox, part of the geartrain assembly. The layshaft (countershaft) carries the constant-mesh gear cluste...
View full detailsHalf shaft 90 HD LH
Half Shaft for the rear axle drive, heavy-duty specification, right-hand side. The half shaft transmits drive from the rear differential to the re...
View full detailsCarburettor Elbow forms the air inlet elbow on the 2.25L 4-cylinder petrol carburettor. It routes intake air into the carburettor throat on instal...
View full detailsHeat Exchanger Cover for the 3.5L V8 twin-carburettor petrol induction system. It encloses the manifold heat-exchanger passage beneath the carbure...
View full detailsIntermediate Exhaust Pipe is a stainless steel replacement for the centre (intermediate) silencer section of the exhaust system. For the 2.5L 200Td...
View full detailsFuel Filter Clasp Fixing Kit that secures the fuel filter clamp housing in the diesel fuel system. Replaces the clasp fixings, which are not suppl...
View full detailsUpgrade or replace your Land Rover Defender 90's rear window surrounds with this OEM-style replacement panel. Designed for all Defender 90 versions...
View full detailsLand Rover Defender 110 Scale Model - a 1:24 scale diecast finished in blue. Reproduces the bodywork, grille and exterior detailing of the Defende...
View full detailsEnsure precise fuel pump removal and installation with this fuel injector locking tool, specifically designed for Land Rover Defender Puma models. ...
View full detailsReduce mud splashes and dirt buildup with these Dirt D-Fenders, designed for Land Rover Defender 90, 110, and 130 models. These smooth-finish D-Fen...
View full detailsLogo Tape is a self-adhesive exterior logo decal, black, 27 cm in length. It is applied to the body panel as exterior lettering.
Freewheeling Hub Conversion Kit - a matched pair of AVM manual locking freewheeling hubs that replace the standard fixed drive flanges on the front...
View full detailsRaised Air Intake relocates the engine air pickup from the standard inner-wing position to roof height. Run up the A-pillar, it draws intake air f...
View full detailsHead Bolt Kit - 2.4 Puma Diesel for the cylinder head of the 2.4 litre Puma (TDCi Duratorq) diesel engine. This kit supplies the full set of cylin...
View full detailsCylinder Head Bolt Kit for the 2.2L Puma (TDCi) turbo diesel engine. Contains the full set of cylinder head bolts that secure the cylinder head to...
View full detailsGearbox Bearing Kit - LT77 - Suffix A-E for overhaul of the LT77 gearbox. This kit supplies the bearings required to rebuild the LT77 five-speed m...
View full detailsGearbox bearing kit Defender LT77 ( suffix H )
Gearbox bearing kit Defender LT77 ( suffix F-G )
Defender door hinge security kit front
Gearbox Guard is an underbody protection plate that mounts beneath the gearbox and transfer box, bolting to the chassis. It shields the gearbox an...
View full detailsFuel Cooler Guard is a bolt-on protective guard that shields the fuel cooler from impact and debris. Mounted over the fuel cooler beneath the vehi...
View full detailsHaynes Restoration Man. - Defender
Door Card forms the finished interior trim panel for the rear side door, covering the inner door frame and concealing the latch linkage and window ...
View full detailsAluminium Gauge Surround Set - a set of four machined aluminium bezels that fit around the instrument gauges as a finished interior trim upgrade. ...
View full detailsFront Coil Springs for the front suspension, raising ride height by approximately 50mm over standard. Supplied as a pair. The raised height increa...
View full detailsRaised Air Intake for the engine air induction system, mounting on the right-hand side of the vehicle. The raised intake relocates the air inlet hi...
View full detailsRaised Air Intake Mantec - 90/110 200TDi
Rear Coil Spring for the rear suspension, raising ride height by approximately 40mm over standard. Wound from 18mm wire with a free height of 445m...
View full detailsLamp Guard Set protects the exterior lamp units from impact damage, fitting over each lens to shield it from knocks by branches, debris and shiftin...
View full detailsMain Wiring Harness forming the primary loom of the vehicle electrical system, running the length of the chassis from connection point HA to JA. I...
View full detailsAnti-Roll Bar Bracket - Left Hand secures the anti-roll bar to the chassis on the left-hand side. Part of the anti-roll (stabiliser) bar assembly,...
View full detailsAnti-Roll Bar Bracket - Right Hand secures the anti-roll bar to the chassis on the right-hand side. Part of the anti-roll (stabiliser) bar assembl...
View full detailsDoor Glass for the front door, right-hand side, in clear glass. This is the main glass panel for the front door, forming part of the door glazing ...
View full detailsDoor Glass for the front door, left-hand side, in clear (un-tinted) glass. This is the sliding window pane that runs in the door channels and is ra...
View full detailsSpecial Bolt
Clutch Lever Pivot Pin for the LT76 gearbox bellhousing. It forms the pivot about which the clutch release lever rotates when the clutch pedal is o...
View full detailsLoad Luggage Carrier - a Mantec-manufactured carrier for stowing luggage and equipment. It provides a dedicated load-carrying platform, expanding ...
View full detailsRear Sill for the left-hand side, in the high cab body configuration. The sill is the structural panel running along the lower edge of the body be...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →