for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Washer Plate
Nut Plate - captive fixing plate used at the rear body upper mountings. The plate holds the nut captive behind a blind or closed panel section, so...
View full detailsFastener Trim Nail used to secure seat trim panels to the seat frame on Land Rover Defender front and centre seat assemblies. This push-fit trim p...
View full detailsSide Window Sliding Catch - RH is the latch that secures the right-hand sliding side window pane in position. Fitted to the sliding glass, it lock...
View full detailsRear Seat Bracket outer left-hand mounting bracket for the rear seating, securing a forward-facing individual rear seat to the floor. Locates the ...
View full detailsFinger Pull, inner, left hand, for horizontally sliding side window glass. The inner pull pairs with the matching outer pull to clamp onto the sli...
View full detailsFinger Pull - Inner - Right-Hand for the door top sliding glass assembly. This inner finger pull is the grip mounted to the inner face of the slid...
View full detailsWeatherseal for the sliding glass in the front door top frame, part of the door glazing and sealing assembly. The seal runs along the glazing chan...
View full detailsSending is only possible by pallet. Too fragile for normal parcel delivery.
Glass
Fixing Plate fitted at the rear of the tailgate latch, from the tailgate assembly. The plate backs the latch mounting on the tailgate, providing t...
View full detailsSoft Top Hood Retainer Spindle for the soft top retaining hardware. The spindle forms part of the hood retainer mechanism, providing the pivot or ...
View full detailsMudflap Stiffener Bracket for the front mudflap assembly. The bracket mounts behind the front mudflap to hold it rigid and maintain its shape, pre...
View full detailsBody Mounting Bracket, left hand, front position, from the rear body mounting arrangement. The bracket forms the interface between the rear body t...
View full detailsBody Mounting Bracket, right hand, front position, from the rear body mounting arrangement. The bracket forms the interface between the rear body ...
View full detailsFuel Injector for the Td5 2.5L 5-cylinder turbo diesel engine. The Td5 uses electronic unit injectors, one per cylinder, seated in the cylinder hea...
View full detailsDoor Lock Striker - LH is the striker that the left-hand door latch engages to hold the door closed. Mounted on the body pillar, it provides the f...
View full detailsDoor Striker – RH is the right-hand striker plate for the rear-end door latch. The door latch engages this striker to draw the door closed and hol...
View full detailsStud Plate for the front sill channel section. Fitted within the front sill channel, this bolt plate provides captive attachment points for sill o...
View full detailsDoor Checker Bracket Assembly - Rear - LH is the door check mechanism for the left-hand rear door. It links the door to the body pillar and limits...
View full detailsDoor Check Strap Bracket – Rear – RH mounts the door check strap on the right-hand rear side door. The check strap limits how far the door swings ...
View full detailsRocksliders Barbarian - Defender 130
1/3 chassis 90 TOT TD5 EXTRA verzendkosten gebruik code AVK40.
Rear Axle Coil Spring Mount Bracket - weld-on bracket forming the coil spring mounting on the rear axle casing. The bracket provides the seat and ...
View full detailsRear Crossmember Cover - a 2mm chequer plate panel in natural aluminium finish that covers the outer face of the rear crossmember. The plate shiel...
View full detailsClutch Slave Cylinder is the hydraulic actuator in the clutch release circuit, converting pressurised fluid from the clutch master cylinder into me...
View full detailsRubber Floor Mat - complete moulded rubber floor covering for the footwell. Provides a fitted, washable floor surface.
Sprocket, Fuel Pump Drive
Body Crossmember - Rear Floor is a structural fabrication forming part of the rear floor framework within the 130 High Capacity Pick-Up (HCPU) load...
View full detailsOil Cooler Seal for the oil cooler and filter assembly on the 2.2L TD4 Diesel. This seal maintains the oil-tight joint at the oil cooler and filte...
View full detailsDesigned for Defender 2007-2016 Smoked lens for a stylish, modern look High-quality 73mm LED light for superior brightness and efficiency Mu...
View full detailsTurbocharger for the Puma 2.2L TDCi 4-cylinder diesel engine, part of the forced induction assembly. The turbocharger uses energy from the exhaust...
View full detailsFront Anti-Roll Bar in the front suspension assembly. It links the left- and right-hand suspension sides to resist body roll during cornering, imp...
View full detailsTiming Chain Guide for the primary timing chain drive of the 2.2L (Puma) diesel engine. The guide bears against the timing chain to control its pa...
View full detailsTiming Chain Guide for the primary timing chain drive of the 2.2L (Puma) diesel engine. The guide bears against the timing chain to control its pa...
View full detailsDoor Lock Cover Plate Seal for the rear-end door latch assembly. The gasket seals the lock cover plate against the door, keeping water and dust ou...
View full detailsExhaust Clamp for the Puma diesel exhaust system, on installations fitted with a diesel particulate filter (DPF). The clamp joins two sections of ...
View full detailsAlternator for the 2.2L 16-valve turbo diesel four-cylinder (Puma) engine. Driven by the auxiliary drive belt, it generates the electrical power t...
View full detailsPuma Heater Glow Plug 2.2
Timing Chain Tensioner
Rear Side Door Seal for the left-hand rear side door. It seals the perimeter of the door aperture against the body frame, keeping out water, dust a...
View full detailsRear Side Door is the complete pressed-steel left-hand rear side door for the four-door station wagon body. The assembly forms the outer and inner...
View full detailsStarter Motor Puma Replacement - Defender
Rear Tailgate Side Seal Hcpu
Turbocharger - 2.4 Duratorq is the complete turbocharger assembly for the Defender Puma 2.4L TDCi four-cylinder diesel engine. This Garrett turboc...
View full detailsTailgate Lock Plate - Branded Galvanised is a galvanised striker plate for the cable-retained tailgate. It provides the anchor point for the tailg...
View full detailsFuel Connector Assembly - 2-Hose in the fuel delivery and pressure-regulation circuit. The connector block forms the union for the fuel lines at th...
View full detailsFuel Injection Pump for the high-pressure common-rail (HPCR) fuel injection system of the 2.4L Duratorq-TDCi (Puma) turbo-diesel engine. The pump ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →